Harmonic Ellipse 3000 Скачать руководство пользователя страница 147

Страница: 147 / 403

Chapter 6 Audio Configuration

147

Ellipse 3000 Release 3.0, Rev. B

Channel Parameters Menu

6.3.1

Activation

The Activation parameter sets the activation mode of the audio channel.

The available options are:

■

Disabled

– Audio channel is disabled.

■

Enabled

– Audio channel is enabled and active.

The Activation default value for the first channel is

Enabled

. The other channels are disabled by

default.

Front Panel

To set the Activation parameter on the front panel:

❖

Navigate

Root > Configuration > Audio > [Audio Channel#] > Channel Parameters > Activation

Web Manager

To set the Activation parameter in the Web Manager Channel Parameters menu:

❖

Select

Audio > Aud#

Activation

1 ‚ Disabled

2 ƒ Enabled

Содержание Ellipse 3000















































































































































































































































































































































































































Результаты поиска

Содержание Ellipse 3000

Отзывы:

Harmonic Ellipse 3000, Руководство пользователя, Страница: 147 / 403

Результаты поиска

Содержание Ellipse 3000

Отзывы: