Harmonic Ellipse 3000 Скачать руководство пользователя страница 291 | Manualshive

Страница: 291 / 403

Harmonic Ellipse 3000 Скачать руководство пользователя страница 291

Chapter 10 Unit Configuration

© 2013 Harmonic Inc. Harmonic All rights reserved.

291

Ellipse 3000 Release 3.0, Rev. B

Alarm Sub-Menu/Tab

Management Port Disconnected

Management port address is not valid

Data Port disconnected

Data port address is not valid

BOOTP failed

Wrong BOOTP parameters for encoder

Wrong Boot File name

BOOTP parameters not suitable for encoder

TFTP Failed

Failure to connect to the TFTP server.

ZAP Failed

NMX ZAP failed

AP_EDH Error on Input

You can enable or disable this alarm. This alarm is active with CRC error
for the Active Picture

FF_EDH Error on Input

You can enable or disable this alarm. This alarm is active with CRC error
for the Full Field

Software Upgrade Failure

Software upgrade failed due to hardware

Other Trafic On Port

Other traffic on the port

Duplicate Sgid

The alarm is triggered by a primary device if another primary device in the
group is detected with same SGID.
For 1:1 scheme the SGID is not user configurable so this alarm is triggered
if more than one primary is configured with the same group ID.

Solution:

Check the other primary devices and find the one with the same Group ID
and same SGID.
For 1:1, find two primary devices with the same GID.

Redundancy Mode Mismatc

Redundancy mode mismatch.

Backup Device is Active

The alarm is triggered by a backup device when it is active.

Solution:

Swap between the primary and the backup.

Primary Device is not Active

The alarm is triggered by a primary device when it is inactive.

Solution:

Check what caused the primary to be inactive, fix the problem then switch
back.

Fail to Sync Configuration

This alarm is triggered by a backup device when it fails to get the primary’s
configuration.

Solution:

Check why the backup can’t get the configuration. It can be due to a
primary problem, primary connectivity (the sync can only be on the
management network) or backup connectivity.

No Available Backup

This alarm is triggered by a primary Ellipse when there is no available
backup Ellipse in the same group with a valid configuration and without
DRT.

Solution:

Check the backup device for

■

Connectivity

■

A valid configuration

If it is already active

«
...
289
290
291
292
293
...
»

Содержание Ellipse 3000




















































































































































































































































































































































































































Отзывы:

Нет отзывов