Harmonic Ellipse 3000 Скачать руководство пользователя страница 107

Страница: 107 / 403

Chapter 4 Transport Stream Configuration

107

Ellipse 3000 Release 3.0, Rev. B

Tables Sub-Menu/Tab

4.4.2

MPEG Tables Sub-Menu/Box

Use the

MPEG Tables

menu to configure the refresh interval for the specific information tables

required by the MPEG SI.

4.4.2.1

Transport Stream ID

The Transport Stream ID parameter sets the transport stream ID number using hexadecimal
numbers.

The range is 0x0 to 0xFFFF (Hexadecimal). The Transport Stream ID default value is

0x1000

Front Panel

4.4.2.2

Network ID

The Network ID parameter sets the Network ID number using hexadecimal numbers.

The range is 0x1 to 0xFFFF (Hexadecimal). The Network ID default value is

0x2000

Front Panel

To set the Network ID parameter on the front panel:

❖

Navigate

Root > Configuration > Transport Stream > DVB-ASI > Network ID

Transport Stream ID

0x1000 [Hex]

<0x0 - 0xffff>

Network ID

0x2000 [Hex]

<0x1 - 0xffff>

Содержание Ellipse 3000















































































































































































































































































































































































































Результаты поиска

Содержание Ellipse 3000

Отзывы:

Похожие инструкции для Ellipse 3000

Бренды по названию

Популярные бренды

Harmonic Ellipse 3000, Руководство пользователя

Результаты поиска

Содержание Ellipse 3000

Отзывы:

Похожие инструкции для Ellipse 3000

Бренды по названию

Популярные бренды