Harmonic Ellipse 3000 Скачать руководство пользователя страница 235

Страница: 235 / 403

Chapter 7 VBI

235

Ellipse 3000 Release 3.0, Rev. B

VBI Lines (Even Fields and Odd Fields)

The following table detailed the VBI information supported by the Ellipse, the line number where
the information is captured and the interface used.

VBI Feature

PAL (576i)

line #

NTSC (480i)

line #

Over CV

Over SDI

Teletext Subtitling

7-22

N/A

Yes

Closed Caption (V-Chip)

21, encoded as
Teletext

Yes

Closed Caption ATSC

N/A

Yes

WSS 23

N/A

Yes

VPS

16 Odd

N/A

Yes

VITC

Decoded on all lines

Yes

Raw Data
(monochrome, analog only)

7-23

10-21

Yes

N/A

AMOL I

N/A

20 Odd,
22 Even

Yes

N/A

AMOL II

N/A

20, 22

Yes

N/A

TV Guide

N/A

10-20

Yes

N/A

Содержание Ellipse 3000















































































































































































































































































































































































































Результаты поиска

Содержание Ellipse 3000

Отзывы:

Harmonic Ellipse 3000, Руководство пользователя, Страница: 235 / 403

Результаты поиска

Содержание Ellipse 3000

Отзывы: