Harmonic Ellipse 3000 Скачать руководство пользователя страница 12

Страница: 12 / 403

Chapter 1 Introduction

Ellipse 3000 Release 3.0, Rev. B

Ellipse 3000 Models and Features

The high level feature-sets follow:

■

VIDEO

❑

Video Compression

• MPEG-2 SD 4:2:0

• MPEG-2 SD 4:2:2 (optional)

• MPEG-2 HD 4:2:0 (optional)

• MPEG-2 HD 4:2:2 (optional)

• MPEG-4 AVC 4:2:0 SD (optional)

• MPEG-4 AVC 4:2:2 SD 8/10 bits (optional)

• MPEG-4 AVC 4:2:0 HD (optional)

• MPEG-4 AVC 4:2:2 HD 8/10 bits (optional)

❑

Profiles and Levels

• MPEG-2 MP@ML

• MPEG-2 MP@HL

• MPEG-4 AVC [email protected]

• [email protected]

❑

Video Formats: PAL / NTSC

❑

Video Resolutions – 480i, 576i, 720p, 1080i

■

AUDIO

❑

Number of Channels – Up to four digital stereo channels AES/EBU, embedded or two analog
channels

❑

Up to eight digital channels AES/EBU, embedded or eight analog channels (optional)

❑

Audio Formats

• MPEG-1 Layer 2

• Dolby® Digital (AC-3) 5.1 passthrough

• AC-3 2.0 (optional)

• MPEG-2 AAC LC (optional)

• MPEG-4 HE-AAC v1, v2 (optional)

• Linear audio passthrough (optional)

• Dolby-E passthrough (optional)

• Operating Modes Joint stereo, single channel, dual channel

• Sampling Frequencies 32, 44.1, 48 kHz

Содержание Ellipse 3000















































































































































































































































































































































































































Результаты поиска

Содержание Ellipse 3000

Отзывы:

Harmonic Ellipse 3000, Руководство пользователя, Страница: 12 / 403

Результаты поиска

Содержание Ellipse 3000

Отзывы: