Harmonic Ellipse 3000 Скачать руководство пользователя страница 179

Страница: 179 / 403

Chapter 6 Audio Configuration

179

Ellipse 3000 Release 3.0, Rev. B

Coding Scheme Configuration

6.5.2.10

Copyright Mark Mode (DD 2.0)

The Copyright Mark parameter indicates whether the information in the Dolby Digital 2.0
encoded bit stream is displayed as protected by copyright.

The available options are:

■

Off

– The information is not protected by copyright.

■

– The information is protected by copyright.

The DD 2.0 Copyright Mark default is

Off

Front Panel

To set the DD 2.0 Copyright Mark parameter on the front panel:

❖

Navigate

Root > Configuration > Audio > [Audio Channel] > DD 2.0 Parameters >

Copyright Mark

Web Manager

To set the DD 2.0 Copyright Mark parameter in the Web Manager:

❖

Select

Audio > Aud#

and access the DD 2.0 Parameters box.

1 ƒ Off

2 ‚ On

Содержание Ellipse 3000















































































































































































































































































































































































































Результаты поиска

Содержание Ellipse 3000

Отзывы:

Harmonic Ellipse 3000, Руководство пользователя, Страница: 179 / 403

Результаты поиска

Содержание Ellipse 3000

Отзывы: