Harmonic Ellipse 3000 Скачать руководство пользователя страница 160 | Manualshive

Страница: 160 / 403

background image

Chapter 6 Audio Configuration

© 2013 Harmonic Inc. Harmonic All rights reserved.

160

Ellipse 3000 Release 3.0, Rev. B

Coding Scheme Configuration

6.5.1.2

Sample Rate (MPEG-1 Layer 2)

The Sample Rate parameter sets the current sampling rate for the MPEG-1 Layer 2 incoming
audio signal. This parameter is used to define the incoming audio quality of the audio input
element device (A/D, digital receiver).

The available options are:

■

32 kHz

■

44.1 kHz

■

48 kHz

The MPEG-1 Layer 2 Sample Rate default value is

48 kHz

.

Front Panel

To set the Sample Rate parameter on the front panel:

❖

Navigate

Root > Configuration > Audio > [Audio Channel] > MPEG-1 Layer 2 Parameters >

Sample Rate

.

Web Manager

To set the MPEG-1 Layer 2 Sample Rate parameter in the Web Manager:

❖

Select

Audio > Aud#

and access the MPEG-1 layer 2 Parameters menu.

Sample Rate

1 ‚ 32 kHz

2 ‚ 44.1 kHz

3 ƒ 48 kHz

«
...
158
159
160
161
162
...
»

Содержание Ellipse 3000




















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Ellipse 3000

Бренд: Atlantis Страницы: 89

ADR87XXXD Series

Бренд: Avue Страницы: 83

DHG-HDD250 - 30-Hour High-Definition Digital Video Recorder

Бренд: Sony Страницы: 2

Handycam HDR-CX610E

Бренд: Sony Страницы: 76

DHG-HDD250 - 30-Hour High-Definition Digital Video Recorder

Бренд: Sony Страницы: 112

Digital 8 DCR-TRV130E

Бренд: Sony Страницы: 140

Бренд: EverFocus Страницы: 2

Бренд: EverFocus Страницы: 68

Бренд: EverFocus Страницы: 128

Бренд: EverFocus Страницы: 147

Бренд: HIKVISION Страницы: 75

Бренд: Clinton Electronics Страницы: 13

Бренд: Vitek Страницы: 2

SAGA VT-ST1640H

Бренд: Vitek Страницы: 2

OnCue Hybrid Series

Бренд: Vitek Страницы: 12

Бренд: Talos Security Страницы: 79

Бренд: GE Security Страницы: 81

Бренд: wbox Страницы: 92

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды