Harmonic Ellipse 3000 Скачать руководство пользователя страница 190 | Manualshive

Страница: 190 / 403

background image

Chapter 6 Audio Configuration

© 2013 Harmonic Inc. Harmonic All rights reserved.

190

Ellipse 3000 Release 3.0, Rev. B

Coding Scheme Configuration

6.5.4.2

Sample Rate (MPEG-2 AAC LC)

The Sample Rate parameter sets the current sampling rate for the incoming MPEG-2 AAC LC
encoded audio signal. This parameter is used to define the incoming audio quality of the audio
input element device (A/D, digital receiver).

The available options are:

■

32

■

44.1

■

48 kHz

The MPEG-2 AAC LC Sample Rate default value is

48 kHz

.

Front Panel

To set the MPEG-2 AAC LC Sample Rate parameter on the front panel:

❖

Navigate

Root > Configuration > Audio > [Audio Channel] > MPEG-2 AAC-LC Parameters >
Sample Rate

.

Web Manager

To set the MPEG-2 AAC LC Sample Rate parameter in the Web Manager:

❖

Select

Audio > Aud#

and access the MPEG-2 AAC LC Parameters box.

Sample Rate

1 ‚ 32 kHz

2 ‚ 44.1 kHz

3 ƒ 48 kHz

«
...
188
189
190
191
192
...
»

Содержание Ellipse 3000




















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Ellipse 3000

Бренд: Codex Страницы: 4

Бренд: Triax Страницы: 24

Бренд: OCB Страницы: 31

iDS-8104AHQXLI-E4

Бренд: HIKVISION Страницы: 224

Бренд: Infinite Play Страницы: 32

Бренд: EverFocus Страницы: 2

Бренд: EverFocus Страницы: 68

Бренд: EverFocus Страницы: 128

Бренд: EverFocus Страницы: 147

Бренд: Planet Networking & Communication Страницы: 93

DS-7204HVI-S Series

Бренд: HIKVISION Страницы: 6

Бренд: Advanced Technology Video Страницы: 22

Бренд: AVer Страницы: 12

Бренд: Clinton Electronics Страницы: 13

Бренд: Clinton Electronics Страницы: 27

Бренд: VC Страницы: 44

Бренд: Steren Страницы: 54

Бренд: Defender Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды