Harmonic Ellipse 3000 Скачать руководство пользователя страница 170

Страница: 170 / 403

Chapter 6 Audio Configuration

170

Ellipse 3000 Release 3.0, Rev. B

Coding Scheme Configuration

6.5.2.1

Encoding Mode (DD 2.0)

The Encoding Mode parameter sets the operation mode of the DD 2.0 audio channel.

The available options are:

■

Mono

– Encoding mode is set to single, mono channel. Mono channel is always left.

■

Stereo

– Encoding mode is set to stereo for encoding a stereophonic audio signal.

The DD 2.0 Encoding mode default value is Stereo.

Front Panel

To set the DD 2.0 Encoding Mode parameter on the front panel:

❖

Navigate

Root > Configuration > Audio > [Audio Channel] > DD 2.0 Parameters >

Encoding Mode

Web Manager

To set the Dolby Digital 2.0 Encoding Mode parameter in the Web Manager:

❖

Select

Audio > Aud#

and access the DD 2.0 Parameters menu.

Encoding Mode

1 ‚ Mono

2 ƒ Stereo

Содержание Ellipse 3000















































































































































































































































































































































































































Результаты поиска

Содержание Ellipse 3000

Отзывы:

Harmonic Ellipse 3000, Руководство пользователя, Страница: 170 / 403

Результаты поиска

Содержание Ellipse 3000

Отзывы: