Harmonic Ellipse 3000 Скачать руководство пользователя страница 249

Страница: 249 / 403

Chapter 9 Input Interface Configuration

249

Ellipse 3000 Release 3.0, Rev. B

IP Input Menu (MPE input)

9.3.1

MPE Menu

The MPE menu allows setting up the MPE parameters.

Front Panel

To access the MPE menu on the front panel:

❖

Navigate

Root > Configuration > Inputs > IP Input > MPE

Web Manager

To access the MPE parameters in the Web Manager:

❖

Select

Inputs > IP INPUT > MPE

9.3.1.1

Activation (MPE IP Input)

The MPE Activation parameter sets the MPE activation mode.

Front Panel

To access the Activation menu on the front panel:

❖

Navigate

Root > Configuration > Inputs > IP Input > MPE > Activation

The available options are:

■

Disabled

– Activation is disabled.

■

Enabled

–Activation is enabled and active.

The MPE Activation default is

Disabled

Web Manager

To set the MPE state in the Web Manager:

❖

Select

Inputs > IP Input > MPE

MPE

1 Activation

2 PID

3 Rate

Activation

ƒ Disabled

‚ Enabled

Содержание Ellipse 3000















































































































































































































































































































































































































Результаты поиска

Содержание Ellipse 3000

Отзывы:

Похожие инструкции для Ellipse 3000

Бренды по названию

Популярные бренды

Harmonic Ellipse 3000, Руководство пользователя

Результаты поиска

Содержание Ellipse 3000

Отзывы:

Похожие инструкции для Ellipse 3000

Бренды по названию

Популярные бренды