Harmonic Ellipse 3000 Скачать руководство пользователя страница 177

Страница: 177 / 403

Chapter 6 Audio Configuration

177

Ellipse 3000 Release 3.0, Rev. B

Coding Scheme Configuration

6.5.2.8

Room Type Mode (DD 2.0)

The Room Type parameter indicates the type and calibration of the mixing room used for the final
Dolby Digital 2.0 audio mixing session.

The available options are:

■

Not Indicated

– Room type is not indicated.

■

Large Room, X Curve Monitor

– Room type is large.

■

Small Room, Flat Monitor

– Room type is small.

The DD 2.0 Room Type default is

Small Room, Flat Monitor

Front Panel

To set the DD 2.0 Room Type parameter on the front panel:

❖

Navigate

Root > Configuration > Audio > [Audio Channel] > DD 2.0 Parameters > Room

Type

Web Manager

To set the DD 2.0 Room Type parameter in the Web Manager:

❖

Select

Audio > Aud#

and access the DD 2.0 Parameters box.

Room Type

1 ‚ Not indicated

2 ‚ Large room; X curve monitor

3 ƒ Small room; flat monitor

Содержание Ellipse 3000















































































































































































































































































































































































































Результаты поиска

Содержание Ellipse 3000

Отзывы:

Harmonic Ellipse 3000, Руководство пользователя, Страница: 177 / 403

Результаты поиска

Содержание Ellipse 3000

Отзывы: