Harmonic Ellipse 3000 Скачать руководство пользователя страница 327

Страница: 327 / 403

Appendix A Characteristics and Capabilities

Processing Capabilities

327

Ellipse 3000 r.3.0, Rev. B

A.4 Processing Capabilities

Video Processing:

■

Video encoding formats:

❑

MPEG-2 4:2:0 MP@ML 8-bit

❑

MPEG-2 4:2:2 P@ML 8-bit

❑

H.264 4:2:0 MP@level3 8-bit

❑

H.264 4:2:0 HP@level4 8-bit

❑

H.264 4:2:2 8-bit

❑

H.264 4:2:2 10-bit

■

Video Latency Modes:

❑

Ultra Low

❑

Low

❑

Standard

❑

Manual

■

Video encoding rates:

❑

4:2:0:

• MPEG-2: 0.3 Mbps

−

80 Mbps

• H.264: 0.3 Mbps

−

75 Mbps

❑

4:2:2: 1.5 Mbps

−

100 Mbps

Video Test Bar

Each video input supports the Broadcast Test Pattern (BAR signal emulation).

Audio Processing:

■

Audio encoding formats:

❑

MPEG-1 layer 2

❑

Dolby

Digital

2.0

❑

Advanced Audio Coding – Low Complexity (MPEG-2 AAC LC)

❑

High Efficiency Advanced Audio Coding (MPEG-4 HE AAC) V1, V2

■

Audio Encoding rates:

❑

MPEG-1 Layer 2: 32 Kbps to 384 Kbps

❑

Dolby

Digital

: 56 Kbps to 640 Kbps

❑

MPEG-2 AAC LC: 32 Kbps to 192 Kbps (stereo)

❑

MPEG-4 HE AAC: 10 Kbps to 72 Kbps

■

Sample Rate Converter (SRC) – Sampling Rates: 32 kHz, 44.1 kHz, 48 kHz

Dolby, Dolby Digital, and Dolby E are registered trademarks of Dolby Laboratories.

Содержание Ellipse 3000















































































































































































































































































































































































































Результаты поиска

Содержание Ellipse 3000

Отзывы:

Harmonic Ellipse 3000, Руководство пользователя, Страница: 327 / 403

Результаты поиска

Содержание Ellipse 3000

Отзывы: