manualshive.com logo in svg

Harmonic Ellipse 3000, Руководство пользователя, Страница: 385 / 403

Поделиться
Скачать
Harmonic Ellipse 3000 Скачать руководство пользователя страница 385

Glossary

Numerics 

 

 

A 

 

B

 



C 

 

 

D 

 



E 

 



F 

 



G  



H  



I  



J  



L 



M 



N 



O 



P 



Q 



R 



S 



T 



U 



V 



W 



Y 

 © 2013 Harmonic Inc.

385

Ellipse 3000 r.3.0, Rev. B

MAC address

The permanent identifier for a device. It consists of six octets separated by colons, for 
example, 00:20:A3:xx:xx:xx. The first six characters identify the manufacturer. Harmonic 
assigns the next six characters as a unique device identifier. 

Max Stream Identifier

The maximum range of the stream identifier. The numbers depend on the number of streams 
and cannot be overlapping with the minimum range. The typical range should be 500 to 
10500. See also

Min Stream Identifier

. 

Mbaud

Megabaud, which is the signal rate of a line, expressed in millions. It can also be the switching 
speed, or number of transitions (voltage or frequency changes), per second. 

MCM

A card for the MN20 multiplexer which converts the M2P output to a SMPTE 310M output. 

MCPC

Multiple Channel Per Carrier. 

MCPC NIM

An MCPC NIM provides connection with wideband communications channels. It supports 15 
to 30 Mbaud. 

MDM

A card for the MN20 multiplexer which provides the means to visually monitor MPEG-2 
transport streams through an onscreen display for

NTSC

video only. The onscreen display 

provides audio and video

PID

and error condition information. 

Mini EIS

An application that allows to configure an

SCS

 network without having a CAS vendor’s Event 

Information Scheduler (EIS). 

Min Stream Identifier

The minimum range of the stream identifier. The numbers depend on the number of streams 
and cannot be overlapping with the maximum range. The typical range should be 500 to 
10500. See also

Max Stream Identifier

. 

mini-DIN connector

This connector, 1/4-inch in diameter, is commonly used for S-video, for example, on the 
Harmonic

MDM

. 

See also

DIN connector

. 

MMDS

Multichannel Multipoint Distribution Service. Uses microwave transmission to deliver 
MPEG-2 transport streams to the end user. 

Содержание Ellipse 3000




















































































































































































































































































































































































































Отзывы:

Нет отзывов