Fuji Xerox ApeosPort-V 4070 Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 719

background image

3 Maintenance

64

M

a

inte
na
nc
e

3

* : The remaining page yield for copy/print jobs is applicable when A4 paper LEF (

) is used. The value is an estimate and varies

depending on the conditions such as the content printed, dot coverage (area coverage), paper size, paper type, copy/print
density, output image type, and the machine operating environment.

Important •

When replacing a toner cartridge, toner may spill and soil the floor. We recommend laying paper on
the floor beforehand.

•

The use of toner cartridges not recommended by Fuji Xerox may degrade image quality and
performance. Use only toner cartridges recommended by Fuji Xerox.

•

When the remaining amount of toner is low, the machine may stop printing and display a message.
If this occurs, replace the toner cartridge to resume copying or printing.

•

Replace toner cartridges while the machine is on.

•

When the machine is in the Power Saver mode, press the <Power Saver> button and then press the
<Machine Status> button on the control panel to exit the Power Saver mode before replacing toner
cartridges.

•

When you replace a toner cartridge with the control panel turned on, press the <Machine Status>
button to check the accurate status of toner cartridge before the replacement.

•

Copy or print density may decrease slightly after the message "Please order a Toner Cartridge"
appears on the touch screen.

•

If you replace a toner cartridge with a partially used toner cartridge, the number of pages that you
can copy or print after the message "Please order a Toner Cartridge" is displayed may differ
significantly from the values described in the above table.

1

Make sure that the machine is not operating,
and open the front cover.

2

Put your hand under the dent of the toner
cartridge, and pull out the cartridge slowly
toward you.

WARNING

z

Never use a vacuum cleaner for spilled toner and residual toner in this product,
toner cartridge or toner container. It may catch fire by electric sparks inside a
vacuum cleaner and cause explosion. Use a broom or a wet cloth to wipe off the
spills. If you spill a large volume of toner, contact your local Fuji Xerox
representative.

z

Never throw a toner cartridge into an open flame. Remaining toner in the
cartridge may catch fire and cause burn injuries or explosion. If you have a used
toner cartridge no longer needed, contact your local Fuji Xerox representative
for its disposal.

«
...
62
63
64
65
66
...
»

Содержание ApeosPort-V 4070
















































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ApeosPort-V 4070

imagePROGRAF W8400

Бренд: Canon Страницы: 24

imagePROGRAF TZ-30000

Бренд: Canon Страницы: 66

imagePROGRAF W7200

Бренд: Canon Страницы: 126

imagePROGRAFi iPF840 series

Бренд: Canon Страницы: 149

Бренд: Canon Страницы: 166

iP4000 - PIXMA Photo Printer

Бренд: Canon Страницы: 2

Бренд: Olympus Страницы: 3

BW Remote Operators Software Kit-A1

Бренд: Canon Страницы: 20

imageRUNNER 2420

Бренд: Canon Страницы: 30

Бренд: Canon Страницы: 51

imageCLASS LBP325dn

Бренд: Canon Страницы: 252

Бренд: DataCard Страницы: 78

Бренд: DataCard Страницы: 8

Бренд: DataCard Страницы: 136

Бренд: DataCard Страницы: 22

Бренд: DataCard Страницы: 16

Бренд: DataCard Страницы: 216

Бренд: DataCard Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды