Fuji Xerox ApeosPort-V 4070 Скачать руководство пользователя страница 452 | Manualshive

Страница: 452 / 719

background image

15 Problem Solving

452

Problem

Solvin

g

15

003-702

[Cause]

You tried to copy sides 1 and 2 of a document simultaneously specifying different
Reduce/Enlarge ratio for each side.

[Remedy] Specify the same Reduce/Enlarge ratio for both sides.

003-703

[Cause]

The Calibration Chart is not detected correctly.

[Remedy] Place the Calibration Chart properly.

003-704

[Cause]

An error is found in the calibration pattern read, and the machine may be out of order.

[Remedy] Execute the calibration again. If the error is not still resolved, contact our Customer

Support Center.

003-705

[Cause]

Copying is started before the machine exits the Power Saver mode and detects the
change for the tray size, when the paper size set in the tray that has been changed
during the Power Saver mode.

[Remedy] Cancel copying, and perform the operation for copying again.

003-750

[Cause]

Unable to store any documents using the 2 Sided Book Copying feature.

[Remedy] Check the 2 Sided Book Copying settings.

Refer to "3 Copy" > "Layout Adjustment" in the User Guide.

003-751

[Cause]

Unable to process the document because the specified scan area is too small.

[Remedy] Increase the resolution or scan area.

003-752

[Cause]

A mix sized document was to be scanned at 600 dpi in Color/2 sided.

[Remedy] Set [Resolution] to [400dpi] or lower, and try scanning again.

003-753

[Cause]

A mix sized document was to be scanned at high resolution, 2 sided.

[Remedy] Set [Resolution] to [200dpi], and scan the document again.

003-754
003-755

[Cause]

An error occurred in the document feeder.

[Remedy] Execute the job again.

003-756

[Cause]

The faxed document is completely blank.

[Remedy] Check whether the document is blank or whether the side of the document to be faxed

is loaded correctly.

003-757

[Cause]

A mix sized document was to be scanned at high resolution, 2 sided.

[Remedy] Set [Resolution] to [300dpi] or lower, and scan the document again.

003-760

[Cause]

An incompatible combination of feature is specified for document scan conditions.

[Remedy] Confirm the selected options.

003-761

[Cause]

The paper size of the tray selected for auto tray differs from the paper size of the tray
selected for Auto Paper selection.

[Remedy] Change the paper size for the tray, or change the [Paper Type Priority] settings.

003-764

[Cause]

Although [Form Overlay] is specified, only one document page is loaded.

[Remedy] Set a document to use as the form document and a document to overlay.

003-780

[Cause]

Failed to compress the scanned document.

[Remedy] Reduce the resolution or the ratio for [Reduce/Enlarge] to decrease the data size, or split

the data to send it separately.

Error Code

Cause and Remedy

«
...
450
451
452
453
454
...
»

Содержание ApeosPort-V 4070
















































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ApeosPort-V 4070

Color imageCLASS MF8580Cdw

Бренд: Canon Страницы: 750

ImageCLASS 2300

Бренд: Canon Страницы: 8

Color imageCLASS MF8580Cdw

Бренд: Canon Страницы: 750

Color imageCLASS 8180c

Бренд: Canon Страницы: 95

Бренд: Canon Страницы: 4

Бренд: Canon Страницы: 49

ImageCLASS 2300

Бренд: Canon Страницы: 156

Бренд: Canon Страницы: 193

Бренд: QMS Страницы: 24

imageCLASS D1120

Бренд: Canon Страницы: 36

ImageCLASS 2300

Бренд: Canon Страницы: 44

Бренд: Canon Страницы: 66

Бренд: Nantian Electronics Страницы: 4

Бренд: Oki Страницы: 4

Бренд: Oce Страницы: 330

Бренд: Ricoh Страницы: 44

Бренд: Citizen Страницы: 3

ECOSYS FS-6530MFP

Бренд: Kyocera Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды