Fuji Xerox ApeosPort-V 4070 Скачать руководство пользователя страница 616 | Manualshive

Страница: 616 / 719

background image

16 Appendix

614

A

p

pe
ndi
x

16

Reduce/Enlarge

54

(Reduce/

Enlarge mode)

Sets the print magnification.
[0] (Default) : Preset %
[1]

: Variable %

[2]

: Fit to Cut Sheet

[Preset %] is a magnification automatically calculated based on [Original
Size] and [Paper Size], and reduces/enlarges the printable area of the
document to fit in the printable area of the output paper. Therefore, when
the size of the document and the output paper are the same, the ratio will be
100%. Also, if [2 Up] is selected, the document will be reduced to the size at
which two pages fit onto one sheet of paper.
[Variable %] is a magnification set in [Variable %] under [Reduce/Enlarge]. A
reference point for scaling (reducing/enlarging) is the upper left corner of the
printable area. This reference point applies to all text, images, and graphics.
[Fit to Cut Sheet] prints the entire cut sheet area onto the printable area of
the output paper. It is a magnification automatically calculated based on
[Original Size] and [Paper Size], and reduces/enlarges the entire document
(including the area outside of the printable area) to fit onto the printable
area of the output paper.

17

(Variable %/

vertical

magnification)

Sets the magnification for the vertical or horizontal direction.
[45 to 210] (Default:100): 45-210%

Note

•

When a continuous form paper is selected for [Original Size], print result is
identical for [Preset %] and [Fit to Cut Sheet].

18

(Variable %/

horizontal

magnification)

2 Up mode

21

Sets whether to print with the 2 Up or page by page. 2 Up is a feature that
prints two pages onto one sheet of paper. Depending on the paper
orientation, the two pages are printed side by side, or one above the other.
[0] (Default) : Off
[1]

: Forward

[2]

: Reverse

Important •

When [Landscape] is selected for [Original Size], print result is identical for
[Forward] and [Reverse].

Output
destination

9

Sets the output tray for the printouts.
[0] (Default) : Center Tray - Lower
[1]

: Side Tray (optional)

[2]

: Center Tray - Upper (optional)

[80]

: Right Middle Tray (optional)

[81]

: Right Top Tray (optional)

Tray 5
confirmation

67

Prints from Tray 5, after you instruct to print and then operate the machine
to start printing.
[0] (Default) : Off
[1]

: On

Grid lines

22

Sets the method for printing double-byte grid lines. The options are as
follows.
[0] (Default) : Image
[1]

: Font

Setting Item

Item Number

Value

«
...
614
615
616
617
618
...
»

Содержание ApeosPort-V 4070
















































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ApeosPort-V 4070

Pixma MG2400 Series

Бренд: Canon Страницы: 2

Бренд: Unitech Страницы: 2

Бренд: Oki Страницы: 80

Бренд: ICT Страницы: 34

Бренд: idp Страницы: 88

ScreenWriter Colour ScreenWriter

Бренд: Xante Страницы: 446

Бренд: Star Micronics Страницы: 127

Бренд: Daewoo Страницы: 37

Oce VarioPrint i Series

Бренд: Canon Страницы: 29

Бренд: Canon Страницы: 138

Oce Arizona 1200 Series

Бренд: Canon Страницы: 226

Бренд: Canon Страницы: 36

Бренд: NEC Страницы: 90

Бренд: Sharp Страницы: 12

Бренд: Sharp Страницы: 12

Бренд: Sharp Страницы: 38

Бренд: Sharp Страницы: 200

Бренд: Sharp Страницы: 194

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды