Fuji Xerox ApeosPort-V 4070 Скачать руководство пользователя страница 531

Страница: 531 / 719

Error Code

531

Problem

Solvin

033-584

[Cause]

An error occurred during IP fax (SIP) transmission.

[Remedy] Confirm the following conditions:

Whether the address or fax number entered is correct

Whether the network cable is connected

Whether the SIP server is enabled

Whether the network cable between the machine and the SIP server connected

Whether the network cable between the machine and the recipient connected

Whether the status of the SIP server and the recipient is available for communications

033-585

[Cause]

An error occurred during IP fax (SIP) transmission.

[Remedy] Contact our Customer Support Center.

033-586

[Cause]

An error occurred during IP fax (SIP) transmission.

[Remedy] Wait for a while, and execute the operation again. And confirm the following conditions:

Whether an IP address can be obtained

Whether the machine can register to the registrar server

033-587

[Cause]

An error occurred during IP fax (SIP) transmission.

[Remedy] Wait for a while, and execute the operation again. And confirm the following conditions:

Whether the network cable is connected

Whether the recipient machine is on

033-588

[Cause]

An error occurred during IP fax (SIP) transmission.

[Remedy] Execute the operation again. If another job is being processed, execute the operation

again.

033-589

[Cause]

An error occurred during IP fax (SIP) transmission.

[Remedy] Check whether or not the recipient’s machine supports IP fax (SIP). If it is IP fax-enabled

device, contact our Customer Support Center.

033-590

[Cause]

An error occurred during IP fax (SIP) transmission.

[Remedy] Confirm the following conditions:

Whether the network cable is connected

Whether the recipient machine is on

033-591

[Cause]

An error occurred during IP fax (SIP) transmission.

[Remedy] Execute the operation again after another processing job finishes.

033-592

[Cause]

An error occurred during IP fax (SIP) transmission.

[Remedy] Confirm the following conditions:

Whether the network cable is connected

Whether the recipient machine is on

033-593

[Cause]

An IP fax (SIP) was cancelled at the sender.

[Remedy] Ask the sender to send again.

033-700

[Cause]

The connection is time out when a fax is send or the machine receives a fax from a
remote machine.

[Remedy] In sending a fax, execute the operation again. In receiving a fax, the remote machine

may cancel sending. Check the situation of the remote machine.

033-710

[Cause]

The document to be sent by polling was deleted.

[Remedy] Store the document again.

Error Code

Cause and Remedy

Содержание ApeosPort-V 4070















































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ApeosPort-V 4070

Отзывы:

Похожие инструкции для ApeosPort-V 4070

Бренды по названию

Популярные бренды

Fuji Xerox ApeosPort-V 4070, Руководство администратора

Результаты поиска

Содержание ApeosPort-V 4070

Отзывы:

Похожие инструкции для ApeosPort-V 4070

Бренды по названию

Популярные бренды