Fuji Xerox ApeosPort-V 4070 Скачать руководство пользователя страница 548 | Manualshive

Страница: 548 / 719

background image

15 Problem Solving

548

Problem

Solvin

g

15

124-701

[Cause]

The output destination was changed because of the malfunction of the specified
output tray (Side Tray).

[Remedy] Contact our Customer Support Center. You can use any output trays other than the

defective output tray.

124-702

[Cause]

The output destination was changed because of the malfunction of the specified
output tray (Finisher Tray).

[Remedy] Contact our Customer Support Center. You can use any output trays other than the

defective output tray.

124-705

[Cause]

The punch setting was cancelled.

[Remedy] Confirm the punch position, and then execute the operation again.

124-706

[Cause]

The folding setting was cancelled.

[Remedy] Confirm the folding setting, and then execute the operation again.

124-708

[Cause]

The output destination has been changed to the Output Tray or the Finisher Tray.
The probable causes are as follows:
1)Paper of a different size from the specified is loaded for 2 sided copying.
2)The Punching feature of the Finisher has malfunctioned.

[Remedy] For 1), check whether the specified size paper is loaded in the tray.

For 2), confirm whether the error code 012-231, 012-232, 012-233, or 012-234 is
displayed on the touch screen, and contact our Customer Support Center.

124-709

[Cause]

The document exceeded the maximum number of pages that can be stapled.

[Remedy] Reduce the number of pages, or cancel the stapling setting, then try printing again.

124-710

[Cause]

The machine cannot output to the output destination specified. A paper size or a paper
type that cannot be output is specified or the output destination fails.

[Remedy] No measure is required. The machine automatically selects the available output

destination. If the paper is not still output from the specified output destination even
after the correct paper size and type is selected, contact our Customer Support Center.

125-311

[Cause]

An error occurred in the machine.

[Remedy] Switch off the machine power, make sure that the touch screen is blank, and then switch

on the machine power. If the same message is displayed again, contact our Customer
Support Center.

127-210
127-211
127-212

[Cause]

A communication error occurred between the machine and the Print Server.

[Remedy] Disconnect the print server cable, and then securely insert the cable into the connector.

Switch off the machine power, make sure that the touch screen is blank, and then switch
on the machine power.

127-213

[Cause]

A communication error occurred between the machine and the Print Server.

[Remedy] Update the machine and the Print Server software to the latest versions.

127-220
127-221

[Cause]

A communication error occurred between the machine and the Print Server.

[Remedy] Disconnect the print server cable, and then securely insert the cable into the connector.

Switch off the machine power, make sure that the touch screen is blank, and then switch
on the machine power.

Error Code

Cause and Remedy

«
...
546
547
548
549
550
...
»

Содержание ApeosPort-V 4070
















































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ApeosPort-V 4070

Бренд: Panasonic Страницы: 32

SPP 2020 - Photo Printer - 20 Sheets

Бренд: Samsung Страницы: 81

Бренд: Samsung Страницы: 98

Бренд: Samsung Страницы: 6

Бренд: Samsung Страницы: 203

Бренд: Samsung Страницы: 264

Бренд: Samsung Страницы: 228

Бренд: Samsung Страницы: 211

Бренд: Samsung Страницы: 5

Бренд: Samsung Страницы: 92

Бренд: Samsung Страницы: 75

Бренд: Samsung Страницы: 11

Бренд: Samsung Страницы: 206

ML 3050 - B/W Laser Printer

Бренд: Samsung Страницы: 103

ML 3050 - B/W Laser Printer

Бренд: Samsung Страницы: 215

Бренд: Samsung Страницы: 2

CLP 510N - Color Laser Printer

Бренд: Samsung Страницы: 266

550N - CLP Color Laser Printer

Бренд: Samsung Страницы: 296

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды