Endress+Hauser HART Proline Promass 83 Скачать руководство пользователя страница 119

Страница: 119 / 148

Proline Promass 83

Technical data

Hauser

119

Flow values (example)

Repeatability

Design fundamentals

→

120.

Material measuring tube: Zirconium 702/R 60702

• Mass flow and volume flow (liquids): ±0.05% o.r.

• Density (liquids): ±0.00025 g/cm

• Temperature: ±0.25 °C ± 0.0025 · T °C; ±0.5 °F ± 0.0015 · (T - 32) °F

Material measuring tube: Tantalum 2.5W

• Mass flow and volume flow (liquids): ±0.05% o.r.

• Mass flow (gases): ±0.25% o.r.

• Density (liquids): ±0.0005 g/cm

• Temperature: ±0.25 °C ± 0.0025 · T °C; ±0.5 °F ± 0.0015 · (T - 32) °F

Influence of medium temperature

When there is a difference between the temperature for zero point adjustment and the
process temperature, the typical measured error of the sensor is ±0.0002% of the full scale
value / °C (±0.0001% of the full scale value/°F).

Influence of medium pressure

The table below shows the effect on accuracy of mass flow due to a difference between
calibration pressure and process pressure.

Turn down

Flow

Maximum measured error

[kg/h]

[lb/min]

[% o.r.]

250 : 1

2.646

2.50

100 : 1

180

6.615

1.00

25 : 1

720

26.46

0.25

10 : 1

1800

66.15

0.10

2 : 1

9000

330.75

0.10

Design fundamentals

→

120

Promass H Zirconium 702/R 60702

Promass H Tantalum 2.5W

[mm]

[inch]

[% o.r./bar]

3/8

–0.017

–0.010

–0.021

–0.005

–0.013

–0.015

1½

–0.018

–0.012

–0.020

–0.016

Содержание HART Proline Promass 83





















































































































































Результаты поиска

Содержание HART Proline Promass 83

Отзывы:

Похожие инструкции для HART Proline Promass 83

Бренды по названию

Популярные бренды

Endress+Hauser HART Proline Promass 83, Руководство по эксплуатации

Результаты поиска

Содержание HART Proline Promass 83

Отзывы:

Похожие инструкции для HART Proline Promass 83

Бренды по названию

Популярные бренды