Endress+Hauser HART Proline Promass 83 Скачать руководство пользователя страница 33

Страница: 33 / 148

Proline Promass 83

Operation

Hauser

5.1.3

Icons

The icons which appear in the field on the left make it easier to read and recognize measured
variables, device status, and error messages.

Icon

Meaning

Icon

Meaning

System error

Process error

Fault message
(with effect on outputs)

Notice message
(without effect on outputs)

| 1 to n

Current output 1 to n

P 1 to n

Pulse output 1 to n

F 1 to n

Frequency output

S 1 to n

Status output/relay output 1 to n

S 1 to n

Totalizer 1 to n

a0001187

Status input

a0001181

Measuring mode;
PULSATING FLOW

a0001182

Measuring mode;
SYMMETRY (bidirectional)

a0001183

Measuring mode;
STANDARD

a0001184

Counting mode, totalizer;
BALANCE (f reverse flow)

a0001185

Counting mode, totalizer;
forward

a0001186

Counting mode, totalizer;
reverse

a0001188

Volume flow

a0001189

Target volume flow

a0001190

Target corrected volume flow

a0001191

Carrier volume flow

a0001192

Carrier corrected volume flow

a0001193

% Target volume flow

a0001194

% Carrier volume flow

a0001195

Mass flow

a0001196

Target mass flow

a0001197

% Target mass flow

a0001198

Carrier mass flow

a0001199

% Carrier mass flow

a0001200

Fluid density

a0001208

Reference density

a0001201

Batching quantity upwards

a0001202

Batching quantity downwards

a0001203

Batch quantity

a0001204

Total batching quantity

a0001205

Batch counter (x times)

a0001207

Fluid temperature

a0001209

Current input

a0001206

Remote configuration

Active device operation via:
• HART, e.g. FieldCare, DXR 375

Содержание HART Proline Promass 83





















































































































































Результаты поиска

Содержание HART Proline Promass 83

Отзывы:

Похожие инструкции для HART Proline Promass 83

Бренды по названию

Популярные бренды

Endress+Hauser HART Proline Promass 83, Руководство по эксплуатации

Результаты поиска

Содержание HART Proline Promass 83

Отзывы:

Похожие инструкции для HART Proline Promass 83

Бренды по названию

Популярные бренды