Endress+Hauser HART Proline Promass 83 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 148

background image

Proline Promass 83

Installation

Hauser

11

3

Installation

3.1

Incoming acceptance, transport and storage

3.1.1

Incoming acceptance

On receipt of the goods, check the following points:
• Check the packaging and the contents for damage.
• Check the shipment, make sure nothing is missing and that the scope of supply matches

your order.

3.1.2

Transport

The following instructions apply to unpacking and to transporting the device to its final
location:
• Transport the devices in the containers in which they are delivered.
• The covers or caps fitted to the process connections prevent mechanical damage to the

sealing faces and the ingress of foreign matter to the measuring tube during
transportation and storage. Consequently, do not remove these covers or caps until
immediately before installation.

• Do not lift measuring devices of nominal diameters > DN 40 (1½") by the transmitter

housing or the connection housing in the case of the remote version (

4). Use webbing

slings slung round the two process connections. Do not use chains, as they could damage
the housing.

• Promass X, Promass O sensor: see special instructions for transporting

#

Warning!
Risk of injury if the measuring device slips. The center of gravity of the assembled measuring
device might be higher than the points around which the slings are slung.
At all times, therefore, make sure that the device does not unexpectedly turn around its axis
or slip.

a0004294

Fig. 4:

Instructions for transporting sensors with > DN 40 (1½")

«
...
9
10
11
12
13
...
»

Содержание HART Proline Promass 83





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для HART Proline Promass 83

Бренд: Major tech Страницы: 8

Бренд: Waltron Страницы: 25

Бренд: Farfisa Страницы: 14

Бренд: Valmet Страницы: 63

Бренд: dbx Страницы: 2

Бренд: Tactical Controls Страницы: 11

Бренд: FarmChem Страницы: 8

Бренд: Kane Страницы: 16

Бренд: Kane Страницы: 60

Бренд: Facom Страницы: 48

Бренд: Garmin Страницы: 22

Бренд: Magene Страницы: 80

SignalHawk SH-36S-PC

Бренд: BIRD Страницы: 137

Бренд: Cal Test Electronics Страницы: 12

Ratio:Guard Advanced

Бренд: H.E. Anderson Страницы: 9

Бренд: TA Instruments Страницы: 68

Бренд: PCE Instruments Страницы: 6

Бренд: Xylem Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды