Endress+Hauser HART Proline Promass 83 Скачать руководство пользователя страница 98 | Manualshive

Страница: 98 / 148

background image

Troubleshooting

Proline Promass 83

98

Hauser

9.6.1

Removing and installing printed circuit boards

Field housing

#

Warning!
• Risk of electric shock. Exposed components carry dangerous voltages. Make sure that the

power supply is switched off before you remove the cover of the electronics compartment.

• Risk of damaging electronic components (ESD protection). Static electricity can damage

electronic components or impair their operability. Use a workplace with a grounded
working surface purposely built for electrostatically sensitive devices!

• If you cannot guarantee that the dielectric strength of the device is maintained in the

following steps, then an appropriate inspection must be carried out in accordance with the
manufacturer’s specifications.

"

Caution!
Use only original Hauser parts.

47, installation and removal:

1.

Unscrew cover of the electronics compartment from the transmitter housing.

2.

Remove the local display (1) as follows:
– Press in the latches (1.1) at the side and remove the display module.
– Disconnect the ribbon cable (1.2) of the display module from the amplifier board.

3.

Remove the screws and remove the cover (2) from the electronics compartment.

4.

Remove power unit board (4) and I/O board (6, 7):
Insert a thin pin into the hole (3) provided for the purpose and pull the board clear of
its holder.

5.

Remove submodules (6.1):
No tools are required for removing the submodules (inputs/outputs) from the I/O
board. Installation is also a no-tools operation.

"

Caution!

Only certain combinations of submodules on the
I/O board are permissible.

The individual slots are marked and correspond to certain terminals in the connection
compartment of the transmitter:

Slot "INPUT / OUTPUT 2" = Terminals 24 / 25
Slot "INPUT / OUTPUT 3" = Terminals 22 / 23
Slot "INPUT / OUTPUT 4" = Terminals 20 / 21

6.

Remove amplifier board (5):
– Disconnect the plug of the sensor signal cable (5.1) including S-DAT (5.3) from the

board.

– Gently disconnect the plug of the excitation current cable (5.2) from the board, i.e.

without moving it back and forward.

– Insert a thin pin into the hole (3) provided for the purpose and pull the board clear of

its holder.

7.

Installation is the reverse of the removal procedure.

«
...
96
97
98
99
100
...
»

Содержание HART Proline Promass 83





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для HART Proline Promass 83

Бренд: ABB Страницы: 20

Бренд: Utilitech Страницы: 2

Бренд: 2B Technologies Страницы: 4

Бренд: Datavideo Страницы: 26

Бренд: Datcon Страницы: 84

Бренд: MadMan Страницы: 37

Бренд: MADDALENA Страницы: 5

Бренд: Mahr Страницы: 384

Бренд: PAT Страницы: 57

Бренд: Parker Страницы: 16

Бренд: Waterproof Страницы: 51

3501B1260KG/M010LN

Бренд: PCB Piezotronics Страницы: 10

QI-POWER-485-300-LV

Бренд: QEED Страницы: 2

Бренд: Quadelectra Audioworx Страницы: 12

Бренд: AEMC Страницы: 16

Бренд: Solight Страницы: 2

Бренд: Omega Страницы: 12

touchMATRIX WDG 053XIOM

Бренд: Wachendorff Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды