Endress+Hauser HART Proline Promass 83 Скачать руководство пользователя страница 12

Страница: 12 / 148

Installation

Proline Promass 83

Hauser

Special instructions for transporting Promass X and O

Warning!
• For transporting use only the lifting eyes on the flanges to lift the assembly.
• The assembly must always be attached to at least two lifting eyes.

A0015790

Fig. 5:

Instructions for transporting Promass O

A0015581

Fig. 6:

Instructions for transporting Promass X

3.1.3

Storage

Note the following points:
• Pack the measuring device in such a way as to protect it reliably against impact for storage

(and transportation). The original packaging provides optimum protection.

• The permissible storage temperature is –40 to +80 °C (–40 to +176 °F), pref20 °C

(+68 °F).

• Do not remove the protective covers or caps on the process connections until you are ready

to install the device.

• The measuring device must be protected against direct sunlight during storage in order to

avoid unacceptably high surface temperatures.

Содержание HART Proline Promass 83





















































































































































Результаты поиска

Содержание HART Proline Promass 83

Отзывы:

Похожие инструкции для HART Proline Promass 83

Бренды по названию

Популярные бренды

Endress+Hauser HART Proline Promass 83, Руководство по эксплуатации

Результаты поиска

Содержание HART Proline Promass 83

Отзывы:

Похожие инструкции для HART Proline Promass 83

Бренды по названию

Популярные бренды