Endress+Hauser HART Proline Promass 83 Скачать руководство пользователя страница 68 | Manualshive

Страница: 68 / 148

background image

Commissioning

Proline Promass 83

68

Hauser

6.3.5

Data backup/transmission

Using the T-DAT SAVE/LOAD function, you can transfer data (device parameters and
settings) between the T-DAT (exchangeable memory) and the EEPROM (device storage
unit).

This is required in the following instances:
• Creating a backup: current data are transferred from an EEPROM to the T-DAT.
• Replacing a transmitter: current data are copied from an EEPROM to the T-DAT and then

transferred to the EEPROM of the new transmitter.

• Duplicating data: current data are copied from an EEPROM to the T-DAT and then

transferred to EEPROMs of identical measuring points.

!

Note!
For information on installing and removing the T-DAT

→

Page 93

ﬀ

.

a0001221-en

Fig. 39:

Data backup/transmission with T-DAT SAVE/LOAD function

Information on the LOAD and SAVE options available:

LOAD: Data are transferred from the T-DAT to the EEPROM.

!

Note!
• Any settings already saved on the EEPROM are deleted.
• This option is only available, if the T-DAT contains valid data.
• This option can only be executed if the software version of the T-DAT is the same or newer

than that of the EEPROM. Otherwise, the error message "TRANSM. SW-DAT" appears after
restarting and the LOAD function is then no longer available.

SAVE:
Data are transferred from the EEPROM to the T-DAT

Esc

E

+

-

XXX.XXX.XX

T-DAT

SAVE/LOAD

Quick Setup

HOME

POSITION

LOAD

YES

NO

CANCEL

SAVE

YES

NO

Restart of the

measuring device

Input is

saved

«
...
66
67
68
69
70
...
»

Содержание HART Proline Promass 83





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для HART Proline Promass 83

Бренд: Kane Страницы: 16

Бренд: Bacharach Страницы: 48

Бренд: Bacharach Страницы: 24

Бренд: Macnaught Страницы: 14

Бренд: Gardner Bender Страницы: 7

Goldmann AT 870

Бренд: Haag-Streit Страницы: 20

Бренд: palintest Страницы: 14

Бренд: PASCO Страницы: 3

Бренд: Magnescale Страницы: 8

Бренд: ICS Schneider Messtechnik Страницы: 40

Frontline 802.11

Бренд: Teledyne Lecroy Страницы: 223

Бренд: Vigor Equipment Страницы: 12

Бренд: HBM Страницы: 84

Бренд: Tektronix Страницы: 116

Бренд: S&T Страницы: 23

WTW pH/ION 3310

Бренд: Xylem Страницы: 48

Бренд: Westfalia Страницы: 18

Бренд: AEMC Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды