Endress+Hauser HART Proline Promass 83 Скачать руководство пользователя страница 26

Страница: 26 / 148

Wiring

Proline Promass 83

Hauser

4.1.2

Cable specification, connecting cable

The specifications of the cable connecting the transmitter and the sensor of the remote
version are as follows:

• 6 × 0.38 mm2 PVC cable with common shield and individually shielded cores
• Conductor resistance:

≤

50 W/km

• Capacitance core/shield:

≤

420 pF/m

• Cable length: max. 20 m (65 ft)
• Permanent operating temperature: max. +105 °C (+221 °F)

Note!
The cable must be installed securely, to prevents movement.

4.2

Connecting the measuring unit

4.2.1

Transmitter connection

Warning!
• Risk of electric shock. Switch off the power supply before opening the device. Do not install

or wire the device while it is connected to the power supply. Failure to comply with this
precaution can result in irreparable damage to the electronics.

• Risk of electric shock. Connect the protective ground to the ground terminal on the

housing before the power supply is applied (not required for galvanically isolated power
supply).

• Compare the specifications on the nameplate with the local supply voltage and frequency.

The national regulations governing the installation of electrical equipment also apply.

Unscrew the connection compartment cover (f) from the transmitter housing.

Feed the power supply cable (a) and the signal cable (b) through the appropriate cable
entries.

Perform wiring:
– Wiring diagram (aluminum housing)

→

– Wiring diagram (stainless steel housing)

→

– Wiring diagram (wall-mount housing)

→

– Terminal assignment

→

Screw the cover of the connection compartment (f) back onto the transmitter housing.

a0004582

Fig. 22:

Connecting the transmitter (aluminum field housing). Cable cross-section: max. 2.5 mm2

Cable for power supply: 85 to 260 V AC, 20 to 55 V AC, 16 to 62 V DC
Terminal

No. 1

: L1 for AC, L+ for DC

Terminal

No. 2

: N for AC, L- for DC

Signal cable: Terminals

Nos. 20–27

→



Ground terminal for protective ground

Ground terminal for signal cable shield

Service adapter for connecting service interface FXA193 (FieldCheck, FieldCare)

Cover of the connection compartment

Securing clamp

– 27

– 25

– 23

– 21

+ 26

+ 24

+ 22

+ 20

L1 (L+)

N (L-)

Содержание HART Proline Promass 83





















































































































































Результаты поиска

Содержание HART Proline Promass 83

Отзывы:

Похожие инструкции для HART Proline Promass 83

Бренды по названию

Популярные бренды

Endress+Hauser HART Proline Promass 83, Руководство по эксплуатации

Результаты поиска

Содержание HART Proline Promass 83

Отзывы:

Похожие инструкции для HART Proline Promass 83

Бренды по названию

Популярные бренды