manualshive.com logo in svg

Dräger Narkomed 2B, Руководство по обслуживанию, Страница: 94 / 308

Поделиться
Скачать
Dräger Narkomed 2B Скачать руководство пользователя страница 94

REPLACEMENT PROCEDURES (continued)

NM2B

4.19.10 Carefully cut the tie strap and remove the other end of the large hose

at the top of the muffler interface wall.

4.19.11 Remove the three socket head screws securing the bellows top plate

to the bellows box.

4.19.12 Carefully cut the tie strap at the intake port (rear of valve) and

remove the large hose.

4.19.13 Disconnect the small diameter tubing from the hose barb on the

bottom of the miniature actuator.

4.19.14 Remove the screws holding the monitor box to the ventilator box.

WARNING:

Two people are required to perform the remaining
portion of the procedure.

4.19.15 Raise the front of the monitor box chassis approximately four inches,

and prop the box open.

WARNING:

Ensure that AC power is removed from the
machine before raising the monitor box. Failure to
observe this precaution may cause injury by
electric shock.

4.19.16 Disconnect the compression fitting at the outboard end of the copper

tube from the valve case assembly, and remove the valve case
assembly.

4.19.17 Carefully position the replacement valve case assembly in the bellows

box, with the copper tube extending up into the ventilator box, and
connect the compression fitting in the ventilator box.

4.19.18 Connect the small diameter tubing to the hose barb on the bottom of

the miniature actuator and secure the connection with a press-on
clamp.

4.19.19 Attach the large hose to the intake port of the new valve case

assembly and secure it with a new tie strap.

4.19.20 Secure the valve case assembly to the bellows top plate with the four

screws that were previously removed. Be sure that the two O-rings
in the bellows top plate are properly seated.

4.19.21 Secure the bellows top plate to the bellows box using the three screws

that were previously removed.

Rev. A

4-62

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

RETURN TO CD-ROM TABLE OF CONTENTS

Содержание Narkomed 2B





















































































































































































































































































































Отзывы:

Нет отзывов