manualshive.com logo in svg

Dräger Narkomed 2B, Руководство по обслуживанию, Страница: 177 / 308

Поделиться
Скачать
Dräger Narkomed 2B Скачать руководство пользователя страница 177

NM2B

PMC PROCEDURE (continued)

For example:

A Narkomed 3 could have recommendation number 21 and failure code 61.1 apply.
21 - No ventilator pressure limit control. Code is B.
61.1 - Enflurane agent is unavailable to test. Code is BC.
Correct certification for this machine is BC, which means CONDITIONALLY CERTIFIED WITH
RECOMMENDATIONS.

A Narkomed 4 could have recommendation numbers 14 and 21 apply.
14 - CO2/Agent monitor exhaust port is not properly connected to the waste gas scavenger.
Code B.
21 - No ventilator pressure limit control. Code B.
The

correct

certification

for

this

machine

is

B,

which

means

CERTIFIED

WITH

RECOMMENDATIONS.

A Narkomed 2B, 2C or GS could have recommendation 30 apply.
30 - Anesthesia machine is equipped with inhalation anesthesia vaporizers without an agent analyzer
in the breathing system. Code B.
The

correct

certification

for

this

machine

is

B,

which

means

CERTIFIED

WITH

RECOMMENDATIONS.

A Narkomed 6000 could have no DMI recommendations or failure codes apply. The correct
certificaiton level for this machine is Code A, CERTIFIED.

Code D, which means NO CERTIFICATION, also means the machine shall not receive a
Periodic Manufacturer’s Certification label. The machine shall also receive a ’WARNING -

This System is Not Certified’ label, P/N 4114857. This label shall be placed at a prominent

location on the right side of the machine after all other previous PM and ’Vigilance Audit®
Validation’ labels have been removed.

Rev.

6-1H

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

RETURN TO CD-ROM TABLE OF CONTENTS

Содержание Narkomed 2B





















































































































































































































































































































Отзывы:

Нет отзывов