Dräger Narkomed 2B Скачать руководство пользователя страница 39

Страница: 39 / 308

NM2B

REPLACEMENT PROCEDURES (continued)

4.2.14

Tighten the regulator mounting setscrews to a torque of 50 to 55 in.
lbs.

4.2.15

Tighten the compression fittings.

4.2.16

Locate the TEE fitting in the ¼ in. diameter regulator output line,
and remove the plug from the TEE fitting.

4.2.17

Set the regulator output pressure in accordance with the Cylinder
Pressure Regulator Adjustment given in Section 5.

4.2.18

Perform the following leak test on the high pressure side of the
regulator:

4.2.18.1

Open the cylinder valve and check for a pressure
indication on the corresponding gauge at the gas
instrumentation panel.

NOTE:

The cylinder used for this test must
contain the following minimum pressure:

: 1000 Psi

700 Psi

: 1000 Psi

800 Psi

AIR

: 1000 Psi

4.2.18.2

Close the cylinder valve and remove the cylinder from the
yoke.

4.2.18.3

For any gas, the pressure should not drop more than 50
Psi in two minutes.

4.2.19

Re-install the cylinder in the yoke.

4.2.20

Replace the table top and its retaining screws.

4.2.21

Replace the top drawer in the cabinet.

4.2.22

Connect the pipeline hoses.

4.2.23

Perform the PMS Procedure given in Section 6.

Rev. A

4-7

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

RETURN TO CD-ROM TABLE OF CONTENTS

Содержание Narkomed 2B





















































































































































































































































































































Результаты поиска

Содержание Narkomed 2B

Отзывы:

Dräger Narkomed 2B, Руководство по обслуживанию, Страница: 39 / 308

Результаты поиска

Содержание Narkomed 2B

Отзывы: