Dräger Narkomed 2B Скачать руководство пользователя страница 232

Страница: 232 / 308

PMC PROCEDURE (continued)

NM2B

6.25A

BELLOWS: PEDIATRIC EXTERNAL - if applicable

6.25A.1

Set the ventilator frequency to 10 BPM.

6.25A.2

Set the I:E Ration to 1:2.

6.25A.3

Adjust the tidal volume to 300 ml/min.

6.25A.4

Turn the ventilator ON.

6.25A.5

Adjust the Inspiratory Flow control on the ventilator to Medium.

6.25A.6

Adjust the fine flow control of the Ped Bellows attachment fully
clockwise.

6.25A.7

Set the O

to 3 l/min.

6.25A.8

Occlude the 15mm patient side of the Y-piece and fill the bellows by
pressing the O

Flush button.

6.25A.9

Observe the absorber breathing pressure gauge as the ventilator cycles.

6.25A.10 What is the pressure when the bellows completes its downward travel?

___cmH

O >30

6.25A.11 What is the pressure when the bellows completes its upward travel?

___cmH

≤

6.25A.12 Verify that with the Pediatric Bellows Fine Flow Control turned fully

counter-clockwise the bellows does not collapse during inspiration.

6.25A.13 Install a 3 L breathing bag onto the patient circuit Y-piece.

6.25A.14 Fill the bellows by pressing the O

Flush button.

6.25A.15 Adjust the O

flow to 10 l/min.

( )

6.25A.16 What is the PEEP? ___cmH

O (

≤

6.25A.17 Adjust the O

flow to 500 ml/min.

( )

6.25A.18 Does the ventilator deliver the full tidal volume during 5 consecutive

cycles? ___(Y)

6.25A.19 Set the ventilator frequency to 20 BPM.

Rev. Y

6-54

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

RETURN TO CD-ROM TABLE OF CONTENTS

Содержание Narkomed 2B





















































































































































































































































































































Результаты поиска

Содержание Narkomed 2B

Отзывы:

Dräger Narkomed 2B, Руководство по обслуживанию, Страница: 232 / 308

Результаты поиска

Содержание Narkomed 2B

Отзывы: