manualshive.com logo in svg

Dräger Narkomed 2B, Руководство по обслуживанию, Страница: 165 / 308

Поделиться
Скачать
Dräger Narkomed 2B Скачать руководство пользователя страница 165

NM2B

ADJUSTMENT AND CALIBRATION PROCEDURES (continued)

5.7

Breathing Pressure Monitor Calibration

5.7.1

Turn the System Power switch to ON.

5.7.2

Press and release the CONFIG key, then simultaneously press the
CONFIG, 21%, and APNEA ALARM DISABLE keys to bring up the
service menu screen.

NOTE:

For this procedure, the keys to the right of the data display will
function as labeled on the display. For example: the TREND key
functions as the EXIT key.

5.7.3

Deleted

5.7.4

Press the CALIBRATION key to bring up the calibration menu
screen.

5.7.5

Disconnect the breathing pressure hose from the absorber.

5.7.6

Connect a test fixture having a TEE connector, an external gauge,
and an inflation device, to the breathing pressure line.

5.7.7

Connect a short hose between the inspiratory and expiratory valves.

5.7.8

Place the Auto/Man selector valve in the BAG position, and turn the
APL valve fully clockwise.

5.7.9

Remove the bag and occlude the bag mount.

5.7.10

Pressurize the circuit to 60 cm H

2

O as shown on the test gauge.

5.7.11

The displayed PRESSURE SPAN (60 cm H20) reading should be
between 465 and 519.

5.7.12

Press the BAROMED key to store the new reading. The message
"PRESSURE SPAN READING STORED" will be displayed.

5.7.13

Press the EXIT key to leave the calibration screen.

5.7.14

Press the EXIT key to leave the service menu screen.

5.7.15

Remove the test fixture from the breathing pressure line, and
reconnect the line to the absorber.

5.7.16

Turn the System Power switch to STANDBY, and restore all
breathing system connections.

Rev. L

5-21

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

RETURN TO CD-ROM TABLE OF CONTENTS

Содержание Narkomed 2B





















































































































































































































































































































Отзывы:

Нет отзывов