Dräger Narkomed 2B Скачать руководство пользователя страница 130

Страница: 130 / 308

REPLACEMENT PROCEDURES (continued)

NM2B

4.28.10 Remove the screws connecting the ground tabs of the keypads to the

hex posts on the floor of the monitor box.

4.28.11 Remove the two hex posts from the floor of the monitor box.

4.28.12 Remove the three filter panel retainer brackets from the back of the

bezel assembly.

4.28.13 Tilt the bottom of the filter panel inward, and remove the panel from

the front bezel. The keypad(s) can then be separated from the filter
panel.

4.28.14 Install the replacement keypad(s) on the filter panel, and carefully

place the filter panel into the front bezel.

4.28.15 Reinstall the filter panel retainer bracket between the CRT panels.

Carefully feed the CRT keypad ground tab through the slot in the
retainer bracket. Reinstall the remaining two retainer brackets.

4.28.16 Reinstall the two hex posts that were previously removed from the

floor of the monitor box.

4.28.17 Carefully connect the keypad ground tabs to the hex posts with the

screws that were previously removed. Be careful not to twist or
damage the ground tabs.

4.28.18 Reinstall the two CRT assemblies. Slide each assembly as far forward

as possible before tightening its mounting screws.

4.28.19 Reinstall the processor assembly and tighten its captive mounting

screws. Reconnect the cables that were previously removed from J1
thru J10 on the processor assembly.

4.28.20 Connect the cables that were previously removed from J7 and J1 on

the power supply assembly.

4.28.21 Place the monitor box top shelf into position, connect its ground wire

to the chassis ground tab, and reinstall the top shelf screws.

4.28.22 Reset the circuit breakers at the back of the monitor box.

4.28.23 Perform the PMS Procedure given in Section 6.

Rev. A

4-98

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

RETURN TO CD-ROM TABLE OF CONTENTS

Содержание Narkomed 2B





















































































































































































































































































































Результаты поиска

Содержание Narkomed 2B

Отзывы:

Dräger Narkomed 2B, Руководство по обслуживанию, Страница: 130 / 308

Результаты поиска

Содержание Narkomed 2B

Отзывы: