Dräger Narkomed 2B Скачать руководство пользователя страница 110

Страница: 110 / 308

REPLACEMENT PROCEDURES (continued)

NM2B

4.22.15 From the back of the flowmeter housing, remove the upper and lower

alarm channel mounting screws.

4.22.16 At the front of the machine, pull the alarm channel assembly

forward, and feed the flowmeter lights wire harness through the hole
at the top of the alarm channel.

4.22.17 Disconnect the orange and orange/white wires from the oxygen supply

pressure alarm switch.

4.22.18 The following steps apply to replacement of the oxygen supply

pressure alarm switch. If the entire alarm channel assembly is being
replaced, skip the next two steps.

4.22.19 Remove the alarm switch from the assembly at point A as shown in

the illustration.

4.22.20 Install the replacement alarm switch with sealing tape on the

threads, and ensure that the switch is oriented on the assembly as
shown in the illustration.

4.22.21 Connect the orange and orange/white wires to the replacement switch

in the same manner as the original.

4.22.22 Feed the flowmeter lights wire harness through the hole at the top of

the alarm channel, and set the alarm channel assembly into place.

4.22.23 Install the upper and lower alarm channel mounting screws.

4.22.24 If applicable, reconnect the flex line from the auxiliary O

flowmeter

and install a new tie strap at the hose barb.

4.22.25 Reconnect the the O

lines, and tighten the three compression

fittings.

4.22.26 Reconnect the cables to J1, J2, J3 and J4 on the alarm circuit board.

4.22.27 Reinstall the front flowmeter and vapor box cover with the six screws

that were previously removed.

4.22.28 Pull the writing or keyboard tray out to its fully extended position.

4.22.29 Locate the tee fitting in the ¼ in. diameter output line of the O

regulator and remove the plug from the tee fitting.

4.22.30 Connect a dedicated O

test gauge to the tee fitting.

4.22.31 Connect AC power to the machine and enable the circuit breakers by

pressing their buttons in.

Rev. A

4-78

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

RETURN TO CD-ROM TABLE OF CONTENTS

Содержание Narkomed 2B





















































































































































































































































































































Результаты поиска

Содержание Narkomed 2B

Отзывы:

Dräger Narkomed 2B, Руководство по обслуживанию, Страница: 110 / 308

Результаты поиска

Содержание Narkomed 2B

Отзывы: