Dräger Narkomed 2B Скачать руководство пользователя страница 197

Страница: 197 / 308

NM2B

PMC PROCEDURE (continued)

6.8.7.1.5 Turn the System Power switch to ON, turn up the oxygen

flow until the system pressurizes to 30 cmH

( )

6.8.7.1.6 What is the value indicated on the flowmeter? ___

(

≤

60ml/min).

6.8.7.1.7 Remove all test equipment, and turn the System Power

switch to STANDBY.

6.8.7.2

Inspiration Valve Leak

6.8.7.2.1 Connect a test terminal to the inspiratory valve.

6.8.7.2.2 Connect a tee fitting (P/N 4109292) and calibrated pressure

meter to the test terminal.

6.8.7.2.3 Connect a pressure bulb to the open port of the tee adapter.

6.8.7.2.4 Connect another test terminal to the bag connector.

6.8.7.2.5 Connect a Capnomed flowmeter to the test terminal on the

bag mount.

6.8.7.2.6 Pressurize the system to 30 cmH

( )

6.8.7.2.7 What is the value indicated on the flow meter? ___ (

≤

ml/min).

6.8.7.2.8 Remove all test equipment.

6.8.7.3

Flow Direction

6.8.7.3.1 Attach a breathing circuit with a 3-liter bag at the Y-piece to

the inspiration and expiration valves.

6.8.7.3.2 Attach a 3-liter bag to the swivel bag mount.

6.8.7.3.3 Turn the System Power switch to ON.

6.8.7.3.4 Set the O

flow to 4 l/min.

6.8.7.3.5 Inflate the simulated lung by briefly using the O

Flush.

6.8.7.3.6 Partially open the APL valve.

Rev. Y

6-19

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

RETURN TO CD-ROM TABLE OF CONTENTS

Содержание Narkomed 2B





















































































































































































































































































































Результаты поиска

Содержание Narkomed 2B

Отзывы:

Dräger Narkomed 2B, Руководство по обслуживанию, Страница: 197 / 308

Результаты поиска

Содержание Narkomed 2B

Отзывы: