Dräger Narkomed 2B Скачать руководство пользователя страница 183

Страница: 183 / 308

NM2B

PMC PROCEDURE (continued)

( )

6.3

BATTERY CIRCUIT

6.3.1

Is "ON" LED lighted? __ (Y)

6.3.2

With the System Power switch ON, unplug the AC power cord.

6.3.3

Is yellow "AC PWR FAIL" LED lighted as long as the power cord is
unplugged? __ (Y)

6.3.4

Does the "AC PWR FAIL" message appear in the Advisory display? __
(Y)

6.3.5

Press and hold the "BATTERY TEST" button.

6.3.6

Is green Battery Test LED lighted as long as "BATTERY TEST" button
is depressed? __ (Y)

6.3.7

Release the "BATTERY TEST" button.

6.3.8

Restore AC power to the machine.

6.3.9

Does the "AC PWR FAIL" message disappear and the LED extinguish?

( )

6.4

CONFIGURATION

6.4.1

Press the CONFIG key on the monitor controls keypad.

6.4.2

The alarm CRT should display the Configuration Screen.

6.4.3

Verify the correct Time and Date.

6.4.4

Adjust the Volume to the highest number.

Rev. Y

6-5

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

RETURN TO CD-ROM TABLE OF CONTENTS

Содержание Narkomed 2B





















































































































































































































































































































Результаты поиска

Содержание Narkomed 2B

Отзывы:

Dräger Narkomed 2B, Руководство по обслуживанию, Страница: 183 / 308

Результаты поиска

Содержание Narkomed 2B

Отзывы: