manualshive.com logo in svg

Dräger Narkomed 2B, Руководство по обслуживанию, Страница: 85 / 308

Поделиться
Скачать
Dräger Narkomed 2B Скачать руководство пользователя страница 85

NM2B

REPLACEMENT PROCEDURES (continued)

4.17

Convenience Outlet AC Power Filter

The convenience outlet AC power filter is located in the back of the ventilator
box near the AC convenience outlets. Access to the power filter requires lifting
the monitor box. Figure 4-17 shows the location of the filter, its connections
and its mounting arrangement.

4.17.1

Set the System Power switch to

STANDBY

and remove AC power

from the machine.

4.17.2

Remove the screws holding the monitor box to the ventilator box.

WARNING:

Two people are required to perform the remaining
portion of this procedure.

4.17.3

Raise the rear of the monitor box chassis approximately two inches,
and prop the box open.

WARNING:

Ensure that AC power is removed from the
machine before raising the monitor box. Failure to
observe this precaution may cause injury by
electric shock.

4.17.4

Remove the two screws holding the safety cover over the AC power
filter, and remove the cover.

4.17.5

Disconnect the AC wiring from each side of the filter.

Note the

position of the wires so they can be re-installed in the same manner.

Rev. A

4-53

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

RETURN TO CD-ROM TABLE OF CONTENTS

Содержание Narkomed 2B





















































































































































































































































































































Отзывы:

Нет отзывов