Dräger Narkomed 2B Скачать руководство пользователя страница 204

Страница: 204 / 308

PMC PROCEDURE (continued)

NM2B

6.12 HIGH PRESSURE REGULATOR

Minimum cylinder pressures for this test are: N2O & CO2: 600 psi

O2, Air, He, He/O2, N2: 1000 psi

6.12.1

Verify the System Power switch is

6.12.2

Verify all cylinder valves are closed except the O

valve.

6.12.3

Set the oxygen flow to 4 liters per min.

6.12.4

Open the other gas flow control valves to drain pressure from the
system.

6.12.5

Close the O

cylinder valve, and press the O

Flush valve to drain

oxygen pressure from the system.

6.12.6

Turn the System Power switch to

STANDBY

6.12.7

Remove the table top from the machine and remove the top cabinet
drawer. Refer to replacement procedure 4.2.

6.12.8

Locate the TEE fitting in the ¼ in. diameter O

regulator output line,

and remove the plug from the TEE fitting.

6.12.9

Connect a dedicated O

test gauge to the TEE fitting.

NOTE:

Two test gauges are required to avoid contamination of the O

circuit

from the other gases: a dedicated test gauge for O

, and a second test

gauge for the other gases.

6.12.10

Open the O

cylinder valve. Turn the System Power switch to

, and

turn the gas selector switch to ALL GASES - if applicable.

6.12.11

Verify the oxygen flow is 4 liters per min.

( )

6.12.12

On the test gauge, what is the regulator output press.? ___PSI (43-49)

NOTE:

Leave the dedicated O

test gauge connected for later use in the Oxygen

Supply Pressure Alarm Test.

6.12.13

Turn the System Power switch to STANDBY.

6.12.14

For the other pressure regulators, locate their corresponding TEE
fittings in the ¼ in. diameter regulator output line, and remove the
plug from the TEE fitting (one at a time).

6.12.15

Connect the second test gauge to the TEE fitting.

Rev. Y

6-26

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

RETURN TO CD-ROM TABLE OF CONTENTS

Содержание Narkomed 2B





















































































































































































































































































































Результаты поиска

Содержание Narkomed 2B

Отзывы:

Dräger Narkomed 2B, Руководство по обслуживанию, Страница: 204 / 308

Результаты поиска

Содержание Narkomed 2B

Отзывы: