Dräger Narkomed 2B Скачать руководство пользователя страница 233

Страница: 233 / 308

NM2B

PMC PROCEDURE (continued)

6.25A.20 Adjust the O

flow to 5 l/min.

( )

6.25A.21 What is the tidal volume on the test volumeter? ___ml (>250)

6.25A.22 Remove the ventilator hose from the ventilator hose terminal.

6.25A.23 Attach a test terminal to the bellows assembly ventilator hose terminal.

6.25A.24 Connect a flowmeter test stand (P/N S000081) to the test terminal.

6.25A.25 Set the frequency to 1 BPM.

6.25A.26 Set the I:E RATIO to 1:1.

( )

6.25A.27 What is the flow indicated during the inspiratory phase? ___(<50 ml)

6.25A.28 Remove the test terminal and flowmeter test stand.

6.25A.29 Return all controls to their original position.

Rev. Y

6-55

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

RETURN TO CD-ROM TABLE OF CONTENTS

Содержание Narkomed 2B





















































































































































































































































































































Результаты поиска

Содержание Narkomed 2B

Отзывы:

Dräger Narkomed 2B, Руководство по обслуживанию, Страница: 233 / 308

Результаты поиска

Содержание Narkomed 2B

Отзывы: