CTI 2500-C100 Скачать руководство пользователя страница 88

Страница: 88 / 113

CTI 2500 Installation and Operation Guide V2.8

Code

Description

Correction

0620

Profibus I/O Error

Indicates that the Profibus interface
experienced a fatal error.

Error details can be obtained from the system
event log.

Clear the error using Partial or Complete restart.
If the action above does not clear the error,
remove the battery and cycle power.
If the error persists, contact CTI product support.

0700

Control block data is invalid

These errors indicate that memory has been
corrupted or that a problem exists in the OS
firmware.

After clearing the error using Partial or Complete
Restart, try reloading the program. If the error
persists, contact CTI product support.

0701

Expression evaluation failed due to
corrupt or invalid expression

0702

SF Execution failed--Program
evaluation data is invalid

0703

Expression evaluation failed due to
corrupt or invalid parameter

0704

SF number from RLL is invalid

Task Code Errors

To aid in diagnosing errors, the following table provides a list of all task code error codes
returned in a task code 00 error reply.

Error Code
(Hexadecimal)

Description

Reset Current Transaction

Address out of Range (other than ladder logic)

Requested data not found

Illegal Task Code Request

Request exceeds available memory

Diagnostic fail on power up

Fatal error detected

Keylock/password protection error

Incorrect amount of data sent with request

Illegal request in current operational mode

Network was not deleted

Attempted write operation did not verify

Illegal number of ASCII characters received

Illegal request when running from EEPROM or flash

Data not inserted

Data not written

Illegal data sent with command

Invalid operation with NIM local/remote mode (obsolete)

The store and forward buffer is busy

No response from special function module

Illegal instruction found in program memory (may include memory
address)

Attempted to write to protected variable (e.g. TCC, TCP)

No response from PLC (e.g. single scan not performed)

Содержание 2500-C100


















































































































Результаты поиска

Содержание 2500-C100

Отзывы:

Бренды по названию

Популярные бренды

CTI 2500-C100, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 2500-C100

Отзывы:

Бренды по названию

Популярные бренды