manualshive.com logo in svg

CTI 2500-C100, Инструкция по установке и эксплуатации

Поделиться
Скачать
CTI 2500-C100 Скачать руководство пользователя страница 79

CTI 2500 Installation and Operation Guide V2.8 

79

 

Status Code 

Status 

U15 

Writing the downloaded bootloader to flash memory 

U16 

Searching for an IO Interface firmware image in flash memory 

U17 

Validating the IO Interface firmware image found in flash memory 

U18 

Copying the IO Interface firmware image from flash memory to DRAM and validating 
copy 

U19 

Writing the IO Interface firmware image to the I/O processor flash memory 

U20 

Checking the Image File in flash memory to see if it is used for manufacturing 
purposes only 

U21 

Checking to see if a Profibus upgrade is needed (based upon CPU hardware) 

U22 

Searching for a Profibus Application Image in the Image File saved in flash memory 

U23 

Searching for a Profibus Loader Image in the Image File saved in flash memory 

U24 

Validating the Profibus Application Image found in flash memory 

U25 

Validating the Profibus Loader Image found in flash memory 

U26 

Copying the Profibus Application Image from flash memory to DRAM and validating 
copy 

U27 

Copying the Profibus Loader Image from flash memory to DRAM and validating copy 

U28 

Writing the Profibus Application to the Profibus processor flash memory 

U36 

Searching for Profibus FPGA image in flash memory 

U37 

Validating Profibus FPGA image found in flash memory 

U38 

Copying Profibus FPGA image from flash memory to DRAM and validating copy 

U39 

Writing Profibus FPGA configuration and boot code to FPGA flash 

 
 

10.5 Firmware Update Errors  

If an error occurs during the firmware update procedure, the procedure will stop and wait for 
corrective action. An error code will be displayed on the MSD. The following table describes the 
error codes and the corrective action.  
 

Error Code  Description  

Corrective Action 

E16 

Firmware update failed 

Rerun the firmware update procedure. If the error 
persists, contact CTI.  

E17 

Unable to write the firmware 
update status flag.  

Rerun the firmware update procedure. If the error 
persists, contact CTI.  

E18 – E25 

Unable to locate or execute the 
main firmware file loader 

Contact CTI.  

E26 

An error was encountered when 
attempting to open the SD card 
file 

Reformat the SD card, copy the firmware file to 
the SD card, and rerun the firmware update 
procedure.   

E27 

The firmware update file could not 
be read 

Delete the firmware update file, re-copy the 
firmware update to the SD card, and rerun the 
firmware update procedure. If the error persists, 
try using a new SD card for the firmware update.  

E28 

The SD card directory could not 
be read 

Reformat the SD card, copy the firmware update 
file to the SD card, and rerun the firmware update 
procedure.   

E29 

No firmware update (.plc) file 
could be found on the SD card or 
more than one firmware update 
file was found.   

One and only one firmware update file is allowed 
on the SD card. This file must be in the root 
directory. Take the necessary action to ensure 
that the desired firmware update file (and only the 
file), is located in the root directory. Once this has 
been done, rerun the firmware update procedure.   

Содержание 2500-C100


















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды