manualshive.com logo in svg

CTI 2500-C100, Инструкция по установке и эксплуатации

Поделиться
Скачать
CTI 2500-C100 Скачать руководство пользователя страница 2

CTI 2500 Installation and Operation Guide V2.8 

ii

 

Copyright 2018 Control Technology Inc. 

All rights reserved. 

 
This manual is published by Control Technology Inc. (CTI) 5734 Middlebrook Pike, 
Knoxville, TN 37921. This manual contains references to brand and product names which 
are tradenames, trademarks, and/or registered trademarks of Control Technology Inc. 
Siemens

®

, SIMATIC

®

, and Series 505

®

, and 505

®

 are registered trademarks of Siemens AG. 

Other references to brand and product names are tradenames, trademarks, and/or 
registered trademarks of their respective holders.  

 

 
 
 

 DOCUMENT DISCLAIMER STATEMENT 

 

Every effort has been made to ensure the accuracy of this document; however, errors do 
occasionally occur.  CTI provides this document on an “as is” basis and assumes no 
responsibility for direct or consequential damages resulting from the use of this document.  
This document is provided without express or implied warranty of any kind, including but not 
limited to the warranties of merchantability or fitness for a particular purpose.  This 
document and the products it references are subject to change without notice.  If you have a 
comment or discover an error, please call us toll-free at 1-800-537-8398 or email us at 

[email protected]

.

 

 
 

REVISION HISTORY

 

V 1.0  

6/28/07 

Initial Release  

V 1.1 

10/30/07 

Defined additional Profibus status bits for STW231. 
Added fatal error code for hardware watchdog event.  
Added information regarding the IPSET utility.  
Added a caution to avoid duplicate IP addresses.  
Changed fatal error section to reflect that the fatal error code will be 
displayed on the MSD.  

V1.2 

 

Corrected error describing STW162 bit 12.  

V1.3 

4/29/08 

Documented STW 455 – STW 501. 
Revised Section regarding Ethernet TCP/IP to improve clarity. 
Revised Appendix C to improve clarity. 
Revised description of SW6 usage to improve clarity.  

V1.4 

6/30/08 

Added section for user flash operation 

V1.5 

10/8/08 

Corrected erroneous status word bit reference in non-fatal error table.  
Added instructions for selecting PRINT jumper 
Added STW191 use for serial port print error reporting.   

V1.6 

12/1/08 

Changed error codes containing a B or D to lower case b or d to 
correspond to multi-segment display.  
Added firmware update status code table.  

V1.7 

2/25/09 

Added a comment requiring all reserved switches to be set to the closed 
position.  

V1.8 

5/11/09 

Added specification of serial port parity, data bits, and stop bits. 
Added instructions for upgrading firmware using the SD card. 
Added description of the duplicate IP detection feature.  

V1.9 

6/11/09 

Added specifications and handling instructions for the lithium battery 

Содержание 2500-C100


















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды