manualshive.com logo in svg

CTI 2500-C100, Инструкция по установке и эксплуатации

Поделиться
Скачать
CTI 2500-C100 Скачать руководство пользователя страница 3

CTI 2500 Installation and Operation Guide V2.8 

iii

 

REVISION HISTORY

 

V1.10 

9/16/09 

Revised Profibus DP cabling specifications to be expressed in meters 
rather than feet.  
Added Belden Hi-Flex cable to recommended Profibus DP cabling.  
Added specifications for maximum number of DP Profibus slaves and 
maximum number of slots per slave.  

V1.11 

11/10/09 

Added specifications for the amount of data per Profibus slave and slots 
per Profibus slave supported by the 2500 controller.  

V1.12 

11/30/09 

Corrected specifications for STW191.  

V1.13 

2/15/10 

Added warning for use of USB port in hazardous environments. 
Added section describing system restart options. 

V1.14 

3/16/10 

Revised text to reflect new features introduced in firmware V6.07.  

•

 

new status bits in STW244 and STW245, 

•

 

fatal error code in STW246,  

•

 

automatic IP address assignment,  

•

 

capability to change IP address in Run mode, 

•

 

expansion of modular slave slots supported from 64 to 128,  

Added a section on Profibus operation to explain Profibus operational and 
synchronization modes and to highlight diagnostic capabilities.  
Corrected serial port pinout diagram in Appendix E.  

V1.15 

9/21/10 

Revised text to reflect new Profibus slave status bit in STW321 (added in 
firmware V6.11). 

V1.16 

11/17/10 

Provided more detail regarding startup errors E9 – E14 

V1.17 

1/10/10 

Corrected error specifying status words for product serial number. 

V1.18 

5/5/11 

Added new error code 102 to the list of fatal errors.   
Corrected a corrupted cross-reference on page 47. 

V1.19 

9/20/11 

Added documentation for dual RBC support  
Revised remote I/O topology drawings to better illustrate dual RBC 
connectivity. 
Updated product pictures to reflect latest front panel overlay. 
Enhanced battery specifications in Appendix B. 
Deleted battery specification in product model table.  

V1.20 

4/21/13 

Added documentation for new functionality enabled by Switch 7 and 8.  
Revised text regarding switches and jumpers to improve clarity.  

V1.21 

4/25/14 

Modified switch drawing to include SW7 and SW8 
Revised text to correct typographic errors and improve clarity 
Updated SD card documentation 

V1.22 

6/26/14 

Added documentation regarding support of additional control relays.  
Added table indicating retentive and non-retentive control relay 
addresses. 
Modified installation instructions to reflect that the controller battery is now 
shipped with the battery installed.  
Created a Battery Replacement appendix. 

V1.23 

7/28/14 

Clarified SD card requirements. Added an SD Requirements appendix.  

V1.24 

4/8/15 

Added a list of all task code errors.  

V1.25 

6/23/15 

Revised the description of the serial port (section 7.2) to include use as a 
printer port.  

V1.26 

9/10/15 

Revised documentation to include new features added in firmware version 
8.02. (Ethernet port IP address change, embedded web server IP 
configuration page, reset to factory default, display subnet in CIDR 
format). 
Added sections to Installation chapter regarding setting IP address and 
automatic IP address assignment.  

Содержание 2500-C100


















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды