manualshive.com logo in svg

CTI 2500-C100, Инструкция по установке и эксплуатации

Поделиться
Скачать
CTI 2500-C100 Скачать руководство пользователя страница 4

CTI 2500 Installation and Operation Guide V2.8 

iv

 

REVISION HISTORY

 

V1.27 

9/17/15 

Corrected error in Appendix C; CIDR notation for subnet mask 
255.255.240.0.  

V1.28 

11/30/15 

Corrected error in firmware update error table for error E30 
Revised text for firmware update error E31 to improve clarity.  

V1.29 

3/1/2016 

Expanded firmware update status codes to include Profibus FPGA (Rev 
G and above) 
Expanded firmware update error codes to include Profibus FPGA (Rev G 
and above) 

V2.0 

8/25/2016 

Added compact PLC (2500C-Cxxx) 
Implemented table of contents hyperlinks 

V2.1 

1/3/2017 

Corrected version support for TISOFT.  

V2.2 

1/26/17 

Corrected illustration of user jumper (p26) 
Updated copyright date 

V2.3 

2/6/2017 

Modified properties of user jumper illustration to correct text positioning. 
Added caption to open Jumper illustration.  

V2.4 

2/14/2017 

Added inline SFP to the potential causes of fatal error 113 in Section 
9.3.2. 

V2.5 

2/27/2017 

Revised description for error E30. 

V2.6 

8/23/2017 

Replaced dipswitch position picture for compact controller models  

V2.7 

12/11/2017 

Added documentation for STW300 – STW330 

V2.8 

4/24/2018 

Added a note to Appendix B stating that status words 243 and above are 
not supported by Siemens 505 controllers.  
Revised note in Firmware Update section that appeared to limit supported 
SD cards to 4GB and below 

 
 

 

Содержание 2500-C100


















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды