manualshive.com logo in svg

CTI 2500-C100, Инструкция по установке и эксплуатации

Поделиться
Скачать
CTI 2500-C100 Скачать руководство пользователя страница 17

CTI 2500 Installation and Operation Guide V2.8 

17

 

1.16 Ethernet Port  

The Ethernet port allows you to connect the controller directly to an Ethernet network using a 
standard RJ-45 connector.  The port automatically selects between 10bT and 100bTX Ethernet 
and between half or full duplex, depending on speed of the device to which it is connected. Two 
status indicators that display Ethernet traffic are embedded into the connector.  

TX- Transmit 

 

Flashes when the port transmits an Ethernet packet.  

RX- Receive

 

Flashes when the port receives an Ethernet packet.  * 

*Ethernet packets received by the port do not necessarily contain data for the controller.   

See Section 7.4 for information regarding use of the Ethernet port.  

1.17 RS-232/ RS-422 Serial Port 

The serial port can support either an RS-232 or an RS-422 electrical interface. When the RS-
232 electrical interface is selected, you can connect to the RS-232 serial port on your PC using 
a standard null modem cable or cables that are currently used with the Siemens Series 505

®

 

controllers. For longer cable runs, you can select the RS-422 electrical interface, which is 
supported by some operator interface equipment.   

The electrical interface and port baud rate via a set of user switches on the controller circuit 
board.  See Section 2.3 for further information regarding the user switches. The other port 
parameters have constant values: Parity = Odd, Data Bits = 7, and Stop Bits = 1.  

Normally, the serial port is used for programming and data access. However, you can change 
the function of the port to a printer port (output only) by repositioning a jumper on the printed 
circuit board (see Section 2.4). You can then use the PRINT statement to send a character 
string to the printer our output device. See the 

CTI 2500 Series Programming Reference Manua

l 

for additional information.  

If your application requires a custom cable, see APPENDIX F. – PRODUCT SPECIFICATIONS 
for the port pinout. 

1.18 Profibus-DP Port 

This port allows you to connect the controller to a standard Profibus-DP network. See 
CHAPTER 4 for more information on using Profibus and APPENDIX F. – PRODUCT 
SPECIFICATIONS for the port pinout. 

1.19  I/O Port    

The I/O port enables you to connect CTI 2500 Series and SIMATIC Series 505

®

 Remote I/O. 

See CHAPTER 4 for additional information regarding remote I/O support and APPENDIX F. – 
PRODUCT SPECIFICATIONS for the port pinout.  
 

 

Содержание 2500-C100


















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды