Brother PE-Design Next Скачать руководство пользователя страница 164

Страница: 164 / 320

162

Tutorial 10-2: Creating Design for Multi-Position Hoops

Step 2

Creating the design

The Design Page appears on the screen as
shown below.

Create the design, making sure that it meets
the following conditions.

• The size of one pattern must be no larger

than 100



100 mm (or 130



180 mm).

• Each pattern must completely fit within a

single area (a, b, or c).

Memo:

• Settings for multi-position hoops are

indicated by “

”.

• Choose the appropriate setting after

checking the size of the hoop available for
your machine.

Memo:

•

Area a

: Embroidering area when the multi-

position hoop is installed at the top
installation position.

•

Area b

: Embroidering area when the multi-

position hoop is installed at the middle
installation position.

•

Area c

: Embroidering area when the multi-

position hoop is installed at the bottom
installation position.
The dotted lines separate each area.

Memo:

1: The position of this pattern is correct since

it fits completely within area a.

2: The position of this pattern is correct since it

fits completely within either area b or area c.

3: The size of this pattern is acceptable, but

its position must be corrected since it does
not fit completely within any of the areas.
(It will be necessary to correct the position
in order to fit in either b or c.)

4: This pattern must be corrected since it is

too large.
(It will be necessary to correct the position
and size in order to fit in either a, b, or c.)

XE8656-001.book Page 162 Monday, May 24, 2010 5:44 PM

Содержание PE-Design Next

































































































































































































































































































































Результаты поиска

Содержание PE-Design Next

Отзывы:

Похожие инструкции для PE-Design Next

Бренды по названию

Популярные бренды

Brother PE-Design Next, Инструкция по эксплуатации

Результаты поиска

Содержание PE-Design Next

Отзывы:

Похожие инструкции для PE-Design Next

Бренды по названию

Популярные бренды