General Circuit Interface (GCI)
17-20
Am186™CC/CH/CU Microcontrollers User’s Manual
■
Monitor Channel Transmit Abort Request Received: Indicates that an abort request
has been received on the monitor channel. This indicates that the receiver on the other
end of the Monitor channel has failed to receive the transmitted data correctly and is
requesting that the current transmission be discontinued and the data transmission be
repeated through software.
■
Monitor Channel End-of-Message Received: Indicates that an EOM has been
received on the monitor channel. This indicates that the message currently being
received has concluded.
■
Monitor Channel Transmit Buffer Available: Indicates that a new byte of data can be
loaded into the Monitor Transmit Data register.
■
Monitor Channel Receive Data Available: Indicates that a byte of data has been
received on the monitor channel and is available in the Monitor Receive Data register.
17.5.9
Software-Related Considerations
To enable the GCI interface, software must set the MODE bit field to 10b in the TSA
Channel A Configuration (TSACON) register. This is necessary regardless of whether TSA
Channel A is being used.
17.5.10
Comparison to Other Devices
The Am186CC microcontroller’s GCI interface is similar to the AMD Am79C30 in clock slave
mode.
17.6
INITIALIZATION
On external and internal reset, the following occurs:
■
The TSAs default to non-GCI mode.
■
The GCI signals default to alternate functionality as shown in Table 17-1 on page 17-3.
■
The EXSYNC bit of the SYSCON register is cleared, making the HDLC Channel C
interface available for raw DCE or PCM highway operation.
■
The MODE field of the TSxCON register is cleared, specifying raw DCE operation.
■
The GCIDEN bit of the HxTCON1 register is cleared, disabling GCI D-Channel control
of the HDLC channel.
■
The MCHEN bit of the GPCON register is cleared, disabling both monitor channels.
■
The MCHSEL bit of the GPCON register is cleared, selecting monitor channel 1.
■
The ICSEL bit of the GPCON register is cleared, selecting IC channel 1.
■
The BRDIS bit of the GPCON register is cleared, enabling bus reversal.
■
The MXBA bit of the GISTAT register is set, indicating that a new byte of data can be
loaded into the GMTD register.
■
All GCI interrupts enables are cleared to 0 in the GIMSK register, masking the interrupts.
■
The TICEN and ECHOEN bits are cleared to 0 in the GTIC register, disabling TIC bus
access and D-channel echo compares, respectively.
Содержание Am186 CC
