DMA Controller
8-16
Am186™CC/CH/CU Microcontrollers User’s Manual
Figure 8-3
DMA Request Sources
DMA Request from Timer 2
The GDxCON0 register can configure a DMA channel to accept the output of Timer 2 as
a DRQ signal to generate periodic data transfers. Note that this feature generates a DRQ
periodically—even if there is no data. To use this feature, software should program Timer 2
with the T2CON register for “continuous” mode—to reach the maximum count and start
counting again. Each time the timer reaches the maximum count, it generates a single
DRQ. The DMA controller latches the Timer 2 DRQ signal to guarantee that the DMA
channel does not miss the DRQ if the bus is not immediately available (e.g., if a higher
priority DMA has control of the bus). If a second Timer 2 DRQ is generated before the first
request is serviced, the second request is lost.
DMA Request from UARTs
Transfers between the DMA and the UARTs are accomplished by programming the
GDxCON0 register to perform transfers between a data buffer (located either in memory
or I/O space) and a serial port data register (SPTXD, SPRXD, HSPTXD, or HSPRXD).
Note: Using a DMA channel with a UART deactivates the corresponding external DMA
request signal.
For DMA
to the UART or High-Speed UART, specify the following configuration details for
the DMA by writing the address of the register into the GDxDSTL and GDxDSTH registers:
the transmit data register (SPTXD or HSPTXD) address; either I/O-mapped or memory-
mapped; as a byte destination, or word destination if using extended writes. The destination
address (the address of the transmit data register) should remain constant throughout the
DMA operation.
For DMA
from the UART or High-Speed UART, specify the following configuration details
for the DMA by writing the address of the register into the GDxSRCL and GDxSRCH
registers: the receive data register (SPRXD or HSPRXD) address; either I/O-mapped or
memory-mapped; as a byte source, or word source if using extended writes. The source
address (the address of the receive data register) should remain constant throughout the
DMA operation.
UART Receiver
UART Transmitter
High-Speed UART Receiver
High-Speed UART Transmitter
Memory or I/O
USB Endpoint A
USB Endpoint B
USB Endpoint C
USB Endpoint D
DRQ
External DRQ signal
Unsynchronized
Transfer
DMA
DRQ Source Select
Timer 2 (latched)
CU
CC
Содержание Am186 CC
