System Overview
Am186™CC/CH/CU Microcontrollers User’s Manual
3-31
The width of the data access should not be modified while the processor is fetching
instructions from the associated address space or while the peripheral control block is
overlaid on the affected address space.
3.6.3.3
Byte Write Enables
The Am186CC/CH/CU microcontrollers provide two signals that act as byte write enables—
WHB (Write High Byte, AD15–AD8) and WLB (Write Low Byte, AD7–AD0). WHB is the
logical OR of BHE and WR (WHB is Low when both BHE and WR are Low). WLB is the
logical OR of A0 and WR (WLB is Low when both A0 and WR are Low).
The byte write enables are driven with the nonmultiplexed address bus as required for the
write timing requirements of common SRAMs.
3.6.3.4
Output Enable
The Am186CC/CH/CU microcontrollers provide the RD (Read) signal, which can act as an
output enable for memory or peripheral devices. The RD signal is Low when the
microcontroller reads a word or byte.
3.6.3.5
Bus Mastering
When an external bus master requests control of the local bus (by asserting HOLD), the
microcontroller completes the bus cycle in progress. It then relinquishes control of the bus
to the external bus master by asserting HLDA and floating S2–S0, AD15–AD0, S6,
TMROUT1, and TMROUT0. During HOLD, internal pullups are active for BHE, DEN, DT/R,
LCS, MCS1/CAS1, MCS2/CAS0, MCS3/RAS1, PCS7–PCS0, PIO4/MCS0, RD, UCS,
WHB, WLB, and WR and an internal pulldown is active for A19–A0 and ALE.
Table 3-8
Programming Am186CC/CH/CU Microcontrollers Bus Width
Space
Register
Bit
Value
Bus Width Comments
UCS
UMCS
USIZ
N/A
N/A
Dependent on boot option
1
Notes:
1. UCS width on reset is determined by the {UCSX8} pin. If {UCSX8} is Low, the bus width is x8; if
{UCSX8} is High, the bus is x16. If UCS boots as 8-bit space, it can be overridden by clearing the
USIZ bit. If UCS boots as 16-bit space, it is not reconfigurable to 8-bit.
LCS
LMCS
LSIZ
N/A
N/A
MCS
MPCS
OMSIZ
0
16 bits
Default
1
8 bits
PCS
2
2. PCS space configured for memory only; not I/O.
MPCS
OMSIZ
0
16 bits
Default
1
8 bits
I/O
3
3. If PCB space is mapped to I/O, its functions are not affected by this bit.
MPCS
IOSIZ
0
16 bits
Default
1
8 bits
Other
Memory
4
4. The remaining memory space that does not reside in one of the enabled, memory, chip-select
regions. If PCB space is mapped to memory, its functions are not affected by this bit.
MPCS
OMSIZ
0
16 bits
Default
1
8 bits
Содержание Am186 CC
