Altera Cyclone V страница 747 Скачать руководство пользователя | Manualshive

Страница: 747 / 1077

background image

If internal DMA controller mode is used for the boot process, the controller performs the following
steps after the Boot ACK Received timeout:

†

• The DMA descriptor is closed.

†

• The

ces

bit in the

idsts

register is set to 1, indicating Boot Data Start timeout.

†

• The

ri

bit of the

idsts

register is not set.

†

c. If the Boot Data Start interrupt is received, it indicates that the boot data is being received from the

card device. When the DMA engine is not in internal DMA controller mode, the software driver can
then initiate a data read from the controller based on the

rxdr

interrupt bit in the

rintsts

register.

†

In internal DMA controller mode, the DMA engine starts transferring the data from the FIFO buffer
to the system memory as soon as the level specified in the

rx_wmark

field of the

fifoth

register

is reached.

†

d. The software driver must terminate the boot process by instructing the controller to send the SD/SDIO

GO_IDLE_STATE command:

†

• Reset the

cmdarg

register to 0.

†

• Set the

start_cmd

bit of the

cmd

register to 1, and all other bits to 0.

†

e. At the end of a successful boot data transfer from the card, the following interrupts are generated:

†

• The

cmd

bit and

dto

bit in the

rintsts

register

†

• The

ri

bit in the

idsts

register, in internal DMA controller mode only

†

f. If an error occurs in the boot ACK pattern (0b010) or an EBE occurs:

†

• The controller does not generate a Boot ACK Received interrupt.

†

• The controller detects Boot Data Start and generates a Boot Data Start interrupt.

†

• The controller continues to receive boot data.

†

• The application must abort the boot process after receiving a Boot Data Start interrupt.

†

g. In internal DMA controller mode:

†

• If the software driver creates more descriptors than required by the received boot data, the extra

descriptors are not closed by the controller.

†

• If the software driver creates fewer descriptors than required by the received boot data, the controller

generates a Descriptor Unavailable interrupt and does not transfer any further data to system
memory.

†

h. If N

AC

is violated between data block transfers, a DRTO interrupt is asserted. Apart from this, if there

is an error associated with the start or end bit, the SBE or EBE interrupt is also generated.

†

The alternative boot operation for eMMC card devices is complete. Do not execute the remaining steps
(

and

).

†

15. Wait for the Command Done interrupt.

†

16. This step handles the case where a start-acknowledge pattern is not expected (

expect_boot_ack

was

set to 0 in

).

†

a. If the Boot Data Start interrupt is not received from the controller within 1 second of initiating the

command (

), the software driver must discontinue the boot process and start with normal

discovery.

†

In internal DMA controller mode:

†

Altera Corporation

SD/MMC Controller

Send Feedback

11-69

Alternative Boot Operation for eMMC Card Devices

cv_54011
2013.12.30

«
...
745
746
747
748
749
...
»

Содержание Cyclone V






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Cyclone V

Бренд: Samsung Страницы: 65

Бренд: Paradyne Страницы: 112

Бренд: ACTi Страницы: 12

Бренд: Supero Страницы: 16

Бренд: ZALMAN Страницы: 8

Mustang-M2AE-MX1

Бренд: IEI Technology Страницы: 58

Бренд: DPS Telecom Страницы: 80

Бренд: Lanpro Страницы: 3

Бренд: Lefroy Brooks Страницы: 10

ExpressCard 11-in-1 Reader/Writer

Бренд: SIIG Страницы: 8

Бренд: Dinstar Страницы: 103

7798 I/SITE LAN

Бренд: CSI Страницы: 56

Бренд: Paradyne Страницы: 46

Бренд: Yeastar Technology Страницы: 2

Meridian 1 Option 11C Mini

Бренд: Meridian Страницы: 546

Schoeps electret

Бренд: VAMISOUND Страницы: 15

Бренд: Curtiss-Wright Страницы: 12

Бренд: Curtiss-Wright Страницы: 58

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды