Altera Cyclone V страница 469 Скачать руководство пользователя | Manualshive

Страница: 469 / 1077

background image

Table 1-1: HPS Address Spaces

Size

Description

Name

4 GB

MPU subsystem

MPU

4 GB

L3 interconnect

L3

4 GB

SDRAM controller subsystem

SDRAM

Address spaces are divided into one or more nonoverlapping contiguous regions. For example, the MPU
address space has the peripheral, FPGA slaves, SDRAM window, and boot regions.

The following figure shows the relationships between the HPS address spaces. The figure is not to scale.

Figure 1-3: HPS Address Space Relationships

0 GB

1 GB

2 GB

3 GB

4 GB

ACP

Window

SDRAM

Region

SDRAM
Window

FPGA

Slaves

Region

Lightweight

FPGA

Slaves

L3

MPU

SDRAM

FPGA

Slaves

Region

Peripheral Region

SDRAM
Window

RAM / SDRAM

Boot Region

(ROM/RAM/SDRAM)

Peripheral Region

The window regions provide access to other address spaces. The thin black arrows indicate which address
space is accessed by a window region (arrows point to accessed address space). For example, accesses to the
ACP window in the L3 address space map to a 1 GB region of the MPU address space.

The SDRAM window in the MPU address space can grow and shrink at the top and bottom (short, blue
vertical arrows) at the expense of the FPGA slaves and boot regions. For specific details, refer to

“MPU

Address Space”

.

The ACP window can be mapped to any 1 GB region in the MPU address space (blue vertical bidirectional
arrow), on gigabyte-aligned boundaries.

The following table shows the base address and size of each region that is common to the L3 and MPU
address spaces.

Table 1-2: Common Address Space Regions

Size

Base Address

Region Name

Identifier

960 MB

0xC0000000

FPGA slaves

FPGASLAVES

Altera Corporation

Introduction to Cyclone V Hard Processor System (HPS)

Send Feedback

1-13

HPS Address Spaces

cv_54001
2013.12.30

«
...
467
468
469
470
471
...
»

Содержание Cyclone V






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Cyclone V

ShareCenter DNS-320L

Бренд: D-Link Страницы: 4

Aquaduct 360 XT

Бренд: Aqua Computer Страницы: 28

ELC-LTTR240-TBP

Бренд: ENERMAX Страницы: 16

Бренд: XtendLan Страницы: 228

Бренд: Eaton Страницы: 14

Бренд: Hauppauge Страницы: 55

E5345 - Xeon 2.33 GHz 8M L2 Cache 1333MHz FSB LGA771 Active Quad-Core Processor

Бренд: Intel Страницы: 112

DVI-Vision-IP-Fiber

Бренд: G&D Страницы: 240

Бренд: Lucent Technologies Страницы: 7

Бренд: ICP DAS USA Страницы: 9

C32C824151 - UB E02 Print Server

Бренд: Epson Страницы: 84

Бренд: Epson Страницы: 168

Бренд: Epson Страницы: 3

Бренд: Enterasys Страницы: 808

Бренд: Cirrus Logic Страницы: 102

Бренд: StarTech.com Страницы: 12

IE-703089-MC-EM1

Бренд: NEC Страницы: 35

DS2000 IntraMail

Бренд: NEC Страницы: 216

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды