manualshive.com logo in svg

Altera Cyclone V, Руководство по эксплуатации устройства, Страница: 429 / 1077

Поделиться
Скачать
Altera Cyclone V Скачать руководство пользователя страница 429

The looped-back data is forwarded to the receiver clock data recovery (CDR). You must provide an alignment
pattern for the word aligner to enable the receiver channel to retrieve the byte boundary.

If the device is not in the serial loopback configuration and is receiving data from a remote device, the
recovered clock from the receiver CDR is locked to the data from the remote source.

For the

phy_serial_loopback

register access description and addressing, refer to the “Loopback

Modes” section of the

Transceiver Reconfiguration Controller

chapter in the

Altera Transceiver PHY

IP Core User Guide

.

Note:

If the device is placed in the serial loopback configuration, the data source to the receiver changes from the
remote device to the local transmitter channel—prompting the receiver CDR to start tracking the phase of
the new data source. During this time, the recovered clock from the receiver CDR may be unstable. Because
the receiver PCS is running off of this recovered clock, you must place the receiver PCS under reset by
asserting the

rx_digitalreset

signal during this period.

When moving into or out of serial loopback, you must assert the

rx_digitalreset

signal for a

minimum of two parallel clock cycles.

Note:

Related Information

Altera Transceiver PHY IP Core User Guide

Forward Parallel Loopback

Forward parallel loopback is a debugging aid to ensure the enabled PCS blocks in the transmitter and receiver
channel function correctly.

Forward parallel loopback is only available in transceiver Native PHY. You enable forward parallel loopback
by enabling the PRBS test mode, through the dynamic reconfiguration controller. You must perform a

rx_digitalreset

after the dynamic reconfiguration operation has completed.

Parallel data travels across the forward parallel loopback path, passing through the RX word aligner, and
finally verified inside the RX PCS PRBS verifier block. Check the operations status from the FPGA fabric.

Figure 6-2: Parallel Loopback Datapath

The following figure shows the parallel PRBS data generated by the TX PCS PRBS generator block.

Transmitter PCS

Transmitter PMA

Receiver PMA

Receiver PCS

FPGA

Fabric

Byte

Ordering

RX

Phase

Compensation

FIFO

Byte

Deserializer

8B/10B

Decoder

Rate

Match

FIFO

Word

Aligner

Deserializer

CDR

TX

Phase

Compensation

FIFO

Byte

Serializer

8B/10B

Encoder

TX

Bit

Slip

Serializer

PRBS Gen

PRBS
Checker

Forward Parallel

Loopback Path

rx_serial_data

tx_serial_data

Usage details for the feature are described in the Altera Transceiver PHY IP Core User Guide.

Note:

Transceiver Loopback Support

Altera Corporation

Send Feedback

CV-53006

Forward Parallel Loopback

6-2

2013.05.06

Содержание Cyclone V






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов